Brocade Communications Systems ServerIron ADX 12.4.00 Service Manual Page 35
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ServerIron ADX Advanced Server Load Balancing Guide 23
53-1002435-01
Configuring SIP SLB
1
Use the following command to configure the maximum number of TCP-based server connections.
ServerIronADX(config)# server sip max-server-tcp-connections 25
Syntax: [no] server sip max-server-tcp-connections <#of connections>
Enter 1 - 64 for <#-of-connections>, which specifies the maximum number of concurrent TCP
connections that ServerIron can actively open to a specific server.
Use the following command to limit the maximum number of TCP transactions.
ServerIronADX(config)# server sip max-tcp-transaction-limit 200,000
Syntax: [no] server sip max-tcp-transaction-limit <#-of-transactions>
The <#of transactions> is the concurrent SIP transactions that a ServerIron can manage. Enter 10
- 300,000 for <#-of-transactions>. The default value is 100,000.
The command should adjust the default number of concurrent SIP transactions supported on a
local BP. Normally, the default value is more than sufficient. Changing this value is not
recommended.
Real server commands for SIP over TCP
The commands in this section are entered under the SIP real server configuration level.
Use the following command to specify the maximum number of SIP connections allowed for a real
server.
ServerIronADX(config-rs1)#sip max-tcp-connections 15
Syntax: [no] sip max-tcp-connections <#of connections>
Enter 1 - 64 for <#of connections>. The default is as follows:
• 64 for connection-reuse cases, source-NAT or non-source-NAT
• For non-connection reuse cases, the value is determined by the value configured for the
max-conn command configured.
NOTE
This command takes precedence over the server sip max-client-tcp-connections and server sip
max-server-tcp-connections (global) commands.
To enable server side connection reuse when Source-NAT is not configured, enter the following
command.
ServerIronADX(config-rs1)# sip enable-tcp-connection-reuse
Syntax: [no] sip enable-tcp-connection-reuse
You can specify an alternate real server IP address for the SIP real server. This is the IP address
that the real server will use to send out SIP requests and responses. This configuration is required
for those SIP servers that may use different IP address other than the configured real server IP
address. It helps a ServerIron to identify the traffic as real server traffic.
- ServerIron ADX 1
- Document History 2
- Contents 5
- About This Document 9
- Command syntax conventions 10
- Notice to the reader 11
- Related publications 11
- Web access 12
- E-mail and telephone access 12
- SIP Server Load Balancing 13
- SIP terminology 16
- SIP message headers 17
- Max-Forwards 18
- Sample deployment topologies 19
- RINGING F4 21
- Configuring SIP SLB 23
- Configuring health check 26
- Example 29
- Load Balancing SIP over TCP 31
- Call-ID3 33
- Call-ID1 34
- Rehashing the SIP hash table 38
- Debug commands 40
- SIP SLB command reference 42
- Sample configuration 43
- Transparent Cache Switching 45
- Stateful caching 47
- Sample Deployment Topologies 48
- TCS with spoofing 49
- TCS with destination NAT 49
- TCS with Source NAT 50
- VIPs with reverse proxy 51
- Configuring TCS 52
- Defining a cache server 53
- Enabling TCS 56
- Other TCS options 57
- Cache Route Optimization 58
- Enabling Destination NAT 62
- Configuring Source NAT 62
- Examples 64
- Distribution algorithm 66
- • Maximum connection rate 72
- Enabling FastCache 73
- Enabling remote cache 73
- Shutting down a cache server 74
- Passive FTP for TCS 75
- Traffic flow of passive FTP 76
- Topologies supported 76
- High availability support 77
- ServerIron ADX 2 78
- Policy based caching 79
- Show commands 81
- Content aware cache switching 82
- Setting up the CSW policies 84
- Configuring the cache servers 85
- This field... Displays 91
- Displaying cache information 95
- TCS information (Continued) 96
- Sample configurations 98
- Applying IP policies 99
- Defining the caches 99
- Defining the cache groups 100
- 53-1002435-01 101
- Policy-based caching 102
- Asymmetric TCS (FastCache) 103
- Policy-based cache failover 105
- TCS with reverse proxy 107
- Layer 3 TCS 109
- Basic TCS configuration 110
- Commands for ServerIron ADX A 111
- Commands for ServerIron ADX B 112
- Internet 114
- 10.10.20.104 114
- 10.10.20.102 114
- Router NI1 117
- Router NI2 117
- OSPF Area 0 117
- Commands for Router NI2 121
- Active-standby TCS 125
- Configuring Router R1 126
- Configuring ServerIron ADX A 126
- Configuring ServerIron ADX B 127
- NetCache servers 128
- NetCache C720 cache server 128
- TABLE 9 Hashing methods 130
- Parsing the host string 133
- Force rehash 136
Related products and manuals for Network switches Brocade Communications Systems ServerIron ADX 12.4.00
(30 pages)© 2020, manymanuals.com. All rights reserved. | 0.501 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals