Brocade Communications Systems Encryption Switch Service Manual Page 299
- Page / 326
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Fabric OS Encryption Administrator’s Guide (DPM) 281
53-1002720-02
Brocade Encryption Switch removal and replacement
6
11. If a master key is not present, restore the master key from a backed up copy. Procedures will
differ depending on the backup media used (for example, recovery smart cards, from the key
vault, from a file on the network, or a file on a USB-attached device). Refer to Chapter 2,
Configuring Encryption Using the Management Application.”
12. Check the EE state using the following command to ensure the EE is online.
FabricAdmin:switch> cryptocfg --show –localEE
NOTE
Because the FS8-18 blade was inserted in the same slot as the previous blade, no change of
HA cluster container ownership is required; the HA cluster configuration is retained.
13. If “manual” failback was set on the HA cluster, you must manually fail back the LUNs owned by
the newly replaced EE.
Brocade Encryption Switch removal and replacement
The following procedures identify steps for removing and replacing a Brocade Encryption Switch.
• For a multi-node replacement, refer to “Multi-node EG Case” on page 281.
• For a single-node replacement, refer to “Single-node EG Replacement” on page 284.
Multi-node EG Case
1. If possible, upload the configuration from the group leader node using the Fabric OS
configupload command.
2. Power off the Brocade Encryption Switch. Remove the Mgmt Link, I/O links, and FC cables from
the Brocade Encryption Switch, noting where each was attached so that the replacement
Brocade Encryption Switch can be cabled properly.
3. From the group leader node, invoke the following command to deregister the old Brocade
Encryption Switch.
Admin:switch> cryptocfg -–dereg –membernode <WWN of old Brocade Encryption
Switch>
4. From the group leader node, invoke the following command to reclaim the WWN base from the
old Brocade Encryption Switch.
Admin:switch> cryptocfg -–reclaim –membernode <WWN of old Brocade Encryption
Switch>
5. Issue commit.
Admin:switch> cryptocfg –-commit
6. Replace the old Brocade Encryption Switch with the new Brocade Encryption Switch and
reconnect the Mgmt link, I/O links, and FC cables.
7. Reconnect the I/O sync ports to the same private LAN as the I/O sync ports of the failed node.
- Fabric OS Encryption 1
- Document History 2
- Contents 3
- 53-1002720-02 10
- About This Document 13
- What’s new in this document 14
- Document conventions 14
- Command syntax conventions 15
- Notes, cautions, and warnings 15
- Additional information 16
- Getting technical help 17
- Document feedback 18
- Encryption Overview 19
- Terminology 20
- The Brocade Encryption Switch 22
- The FS8-18 blade 23
- FIPS mode 23
- Performance licensing 23
- Usage limitations 24
- FIGURE 2 Encryption overview 25
- FIGURE 3 Frame redirection 26
- IO Sync LAN 27
- FIGURE 5 DEK life cycle 28
- Master key management 29
- Support for virtual fabrics 29
- Encryption Center features 32
- Encryption user privileges 33
- Smart card usage 34
- Using system cards 39
- Deregistering system cards 41
- Using smart cards 41
- Tracking smart cards 42
- Editing smart cards 44
- Network connections 45
- Blade processor links 45
- (KAC) certificate 46
- Encryption preparation 53
- Creating an encryption group 53
- Creating HA clusters 70
- Failback option 72
- Invoking failback 72
- Adding an encryption target 73
- FIGURE 46 Next Steps screen 81
- Configuring storage arrays 89
- Remote replication LUNs 89
- SRDF pairs 90
- Moving targets 94
- Tape LUN statistics 97
- Encryption engine rebalancing 102
- Master keys 103
- Active master key 104
- Alternate master key 104
- Master key actions 104
- ATTENTION 106
- Creating a master key 111
- Security Settings 112
- Setting zeroization 113
- Redirection zones 115
- Disk device decommissioning 115
- Decommissioning disk LUNs 116
- Displaying Universal IDs 118
- Setting disk LUN Re-key All 119
- Thin provisioned LUNs 123
- Thin Provisioning support 124
- Time left for auto rekey 125
- General tab 131
- Members tab 133
- Members tab Remove button 134
- Security tab 135
- HA Clusters tab 137
- Tape Pools tab 139
- Adding tape pools 140
- Engine Operations tab 141
- TABLE 3 Encryption acronyms 142
- In this chapter 143
- Overview 144
- Command validation checks 144
- (Continued) 146
- Cryptocfg Help command output 148
- Management LAN configuration 148
- Configuring cluster links 149
- Node is a group leader node 150
- Node is a member node 150
- • FIPS crypto officer 151
- • FIPS user 151
- • Node CP certificate 151
- Submitting the CSR to a CA 154
- • cryptocfg --initEE 161
- • cryptocfg --regEE 161
- • cryptocfg --enableEE 161
- High availability clusters 166
- Creating an HA cluster 167
- Policy Configuration Examples 170
- Re-exporting a master key 171
- Viewing the master key IDs 172
- Zoning considerations 175
- Frame redirection zoning 176
- Gathering information 180
- Crypto LUN configuration 184
- Discovering a LUN 185
- Configuring a Crypto LUN 186
- Configuring a tape LUN 189
- Decommissioning LUNs 193
- SRDF LUNs 198
- --set -replication enable 199
- Adding replication LUNs 200
- Reading metadata after sync 200
- -newLUN option 201
- TF snapshot rekeying details 207
- -not_ready option of TF 208
- <initiator PWWN> 208
- ID> <initiator PWWN> 210
- Tape pool configuration 212
- CommVault Galaxy labeling 213
- NetBackup labeling 213
- Creating a tape pool 214
- Deleting a tape pool 215
- Modifying a tape pool 215
- First-time encryption 220
- Space reclamation 222
- Data rekeying 223
- Deployment Scenarios 227
- --rdcreate [host wwn] 236
- FIGURE 103 FCIP deployment 238
- Data mirroring deployment 239
- VMware ESX server deployments 241
- General guidelines 244
- HP-UX considerations 248
- Enabling a disabled LUN 249
- AIX Considerations 249
- Disk metadata 250
- Tape metadata 250
- Tape data compression 251
- Tape pools 251
- Tape block zero handling 252
- Tape key expiry 252
- Avoid double encryption 254
- PID failover 254
- Manual rekey 255
- Latency in rekey operations 255
- Key Vault Best Practices 259
- Tape Device LUN Mapping 259
- Deleting an encryption group 265
- Removing an HA cluster member 265
- Deleting an HA cluster member 269
- Failover/failback example 270
- Recovery 271
- -hbmisses and -hbtimeout 276
- Key vault diagnostics 282
- Command Activity 285
- Problem Resolution 285
- General errors and conditions 286
- LUN policy troubleshooting 293
- MPIO and internal LUN states 295
- Multi-node EG replacement 296
- Single-node EG replacement 298
- Multi-node EG Case 299
- Single-node EG Replacement 302
- Deregistering a DPM key vault 305
- TABLE 15 Compatibility Matrix 308
- State and Status Information 311
- Security processor KEK status 312
- Encrypted LUN states 312
- TABLE 22 Tape LUN states 315
Related products and manuals for Network switches Brocade Communications Systems Encryption Switch
(34 pages)
(120 pages)© 2020, manymanuals.com. All rights reserved. | 2.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals