Brocade Communications Systems StorageWorks 4400 Enterprise V User's Guide Page 24
- Page / 128
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Figure 12 shows the back view of the HSV300–S controller enclosure
Management module
The web-based operator control panel (WOCP) provides a direct interface to the management module
within each controller. From the WOCP you can display storage system status and configuration
information, shut down the storage system, and manage the password. For tasks to perform with the
WOCP, see the WOCP online help.
The WOCP provides two levels of administrator access and an interface for firmware updates to the
management module. For additional details about the WOCP, see the WOCP online help.
Controller status indicators
The status indicators display the operational status of the controller. The function of each indicator is
described in Table 7. During initial setup, the status indicators might not be fully operational.
Each port on the rear of the controller has an associated status indicator located directly above it.
Table 5 lists the port and its status description for the HSV300. Table 6 lists the port and its status
descriptions for the HSV300–S.
Table 5 HSV300 controller port status indicators
DescriptionPort
• Green — Normal operation
• Amber — No signal detected
•
Off — No SFP
1
detected or the Direct Connect WOCP setting is incorrect
Fibre Channel host ports
• Green — Normal operation
• Amber — No signal detected or the controller has failed the port
•
Off — No SFP
1
detected
Fibre Channel device ports
1
On copper Fibre Channel cables, the SFP is integrated into the cable connector.
Table 6 HSV300-S controller port status indicators
DescriptionPort
• Green on — Normal operation or loopback port
• Green flashing — Normal online I/O activity
• Amber on — Faulted port, disabled due to diagnostics or Portdisable
command
• Amber flashing — Port with no synchronization, receiving light but not
yet online or segmented port
•
Off — No SFP
1
, no cable, no license detected.
Fibre Channel switch ports
• Green — Normal operation
• Amber — No signal detected or the controller has failed the port
•
Off — No SFP
1
detected
Fibre Channel device ports
EVA4400 hardware24
- Array user guide 1
- Contents 3
- About this guide 11
- HP technical support 13
- Customer self repair 13
- Rack stability 13
- Subscription service 13
- HP websites 14
- Documentation feedback 14
- 1 EVA4400 hardware 15
- M6412 disk enclosures 16
- I/O modules 17
- I/O module status indicators 18
- Copper Fibre Channel cables 19
- Fibre Channel disk drives 20
- Controller enclosures 21
- Controller status indicators 24
- Power supplies 25
- Fan module 26
- Battery module 27
- HSV controller cabling 27
- Storage system racks 28
- Power distribution 28
- CXO5409B 29
- 4. AC receptacles1. PDU 1 30
- 5. Mounting hardware2. PDU 2 30
- 3. Circuit breakers 30
- EVA4400 hardware30 30
- Rack AC power distribution 31
- Moving and stabilizing a rack 33
- EVA4400 hardware34 34
- 1. Hex nut 35
- 2. Leveler foot 35
- EVA4400 hardware36 36
- 2 EVA4400 operation 37
- BehaviorPoint in timeSetting 38
- Implicit LUN transition 39
- EVA4400 operation40 40
- Starting the storage system 41
- EVA4400 operation42 42
- EVA4400 operation44 44
- Recovery firmware CD 46
- Handling fiber optic cables 46
- EVA4400 operation48 48
- 3 Replacing array components 49
- Replaceable parts 50
- Replacement instructions 52
- Replacing array components54 54
- 4 Single path implementation 55
- Recommended mitigations 56
- Supported configurations 56
- HP-UX configuration 58
- Limitations 59
- Requirements 60
- HBA configuration 60
- SUN Solaris configuration 63
- OpenVMS configuration 65
- NetWare configuration 66
- Linux (32-bit) configuration 67
- Linux (Itanium) configuration 69
- IBM AIX configuration 71
- VMware configuration 72
- Failure scenarios 74
- Sun Solaris 75
- Failure effectFault stimulus 76
- 5 Error messages 79
- Error messages92 92
- A Regulatory notices 93
- Class A equipment 94
- Class B equipment 94
- Modifications 94
- Laser device 95
- Notice for the European union 96
- Notice for France 96
- WEEE Recycling Notices 96
- Czechoslovakian notice 97
- Estonian notice 97
- Dutch notice 97
- Finnish notice 98
- French notice 98
- German notice 98
- Greek notice 99
- Hungarian notice 99
- Italian notice 99
- Latvian notice 99
- Lithuanian notice 100
- Polish notice 100
- Portuguese notice 100
- Slovakian notice 100
- Germany noise declaration 101
- Japanese notice 102
- Taiwanese notice 102
- Japanese power cord notice 102
- Regulatory notices104 104
- Internal component envelope 105
- EIA310-D standards 105
- Airflow and Recirculation 106
- Configuration Standards 107
- UPS Selection 107
- Glossary 109
- Glossary110 110
- Glossary112 112
- Glossary114 114
- Glossary116 116
- Glossary118 118
- Glossary120 120
- Glossary122 122
- Glossary124 124
Related products and manuals for Network switches Brocade Communications Systems StorageWorks 4400 Enterprise V
Network switches Brocade Communications Systems AA979A - StorageWorks SAN Switch 2/8V User's Guide
(46 pages)
(46 pages)
Network switches Brocade Communications Systems AA979A - StorageWorks SAN Switch 2/8V User Manual
(11 pages)
(11 pages)
© 2020, manymanuals.com. All rights reserved. | 2.281 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals