Brocade Communications Systems Brocade Superx Series Installation Guide Page 14
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2 Brocade FastIron SX Series Chassis Hardware Installation Guide
53-1002500-01
Overview
1
PoE port density
Table 1 shows the maximum PoE port density for the FastIron X Series chassis devices.
NOTE
For PoE+ port density, refer to “PoE+ port density” on page 2.
PoE+ port density
NOTE
PoE+ is supported on the FI-SX-24-GPP and FI-SX48GPP interface modules for FSX 800 and FSX
1600 devices only.
To determine the maximum number of PoE+ Class (30W) ports available per power supply, use the
calculation: One power supply (1080W) over power consumed by PoE+ port (30W)= 1080W/30W =
36 ports.
Table 2 shows the maximum PoE+ port density for the FI-SX-24-GPP and FI-SX48GPP interface
modules.
TABLE 1 Maximum number of PoE class 3 (15.4W) ports per power supply
Power Supply Number of Power
Supplies
FSX 800 FSX 1600
SX-ACPWR-PoE and
SX-DCPWR-PoE
17070
SX-ACPWR-PoE and
SX-DCPWR-PoE
2140140
SX-ACPWR-PoE and
SX-DCPWR-PoE
3N/A210
SX-ACPWR-PoE and
SX-DCPWR-PoE
4 N/A 280
SX-ACPWR2500-PoE 1 146 140
SX-ACPWR2500-PoE 2 292
1
1. The FSX 800 supports a maximum of 192 PoE ports. The FSX 1600 supports a maximum of 384
PoE ports.
280
SX-ACPWR2500-PoE 3 N/A 438
1
SX-ACPWR2500-PoE 4 N/A 584
1
TABLE 2 Maximum number of PoE+ class (30W) ports per power supply
Power Supply Number of
Power Supplies
FSX 800 FSX 1600
SX-ACPWR-PoE and
SX-DCPWR-PoE
136 36
SX-ACPWR-PoE and
SX-DCPWR-PoE
272 72
SX-ACPWR-PoE and
SX-DCPWR-PoE
3N/A 108
- Brocade FastIron SX Series 1
- Document History 2
- Contents 3
- About This Document 9
- Text formatting 10
- Command syntax conventions 10
- Notice to the reader 11
- Related publications 11
- Document feedback 12
- Product Overview 13
- PoE port density 14
- PoE+ port density 14
- Software features 15
- PoE and PoE+ applications 16
- Support for IPv6 modules 16
- Hardware features 16
- FSX 800 chassis 17
- FIGURE 2 FSX 800 module slots 18
- FSX 1600 chassis 19
- FIGURE 4 FSX 1600 slots 21
- Management modules 22
- Switch fabric modules 25
- Interface modules 25
- Hot swap support 26
- LED Position State Meaning 28
- 2Port 2 14Port 14 29
- • 24 10/100/1000 copper ports 30
- • 24 LEDs for port status 30
- • 24 LEDs for PoE status 30
- • 24 LEDs 32
- 1Port 1 13 Port 13 35
- 2Port 2 24 Port 24 35
- Network interfaces 37
- Port regions 38
- Power supplies 39
- • Non-PoE devices: 40
- • PoE devices: 40
- • PoE+ devices: 41
- 2nd POE Power Supply 42
- Replacement power supplies 43
- SYSEJECT 44
- Power supply LEDs 45
- Cooling system 46
- Built-in mounting brackets 47
- Unpacking the system 49
- Installation precautions 50
- Cabling infrastructure 53
- Installation location 53
- Removing the slot panels 57
- Powering on the system 64
- Rear View Detail 69
- • Verify that the connection 71
- • Make sure that the power 71
- • Make sure that the wall 71
- Displaying the module status 72
- Assigning permanent passwords 75
- Configuring IP addresses 77
- Brocade# erase startup-config 78
- Brocade# configure terminal 78
- Brocade(config)# 78
- Brocade(config)# int e 1/5 78
- IPv6 devices 79
- Brocade> enable 81
- Connecting network devices 82
- Using a CX4 transceiver 85
- Testing network connectivity 86
- LED Desired 87
- Field Definition 92
- Managing the cooling system 94
- 4High 50 C80 C 100 78 dB 97
- 3Medium49 C59C 50 66 dB 97
- 1Low N/A 57 C 25 56 dB 97
- Monitoring the cooling system 99
- Displaying the temperature 100
- This Field... Displays 101
- Static and dynamic buffers 102
- (FSX 800 and FSX 1600 only) 103
- 53-1002500-01 104
- Removing MAC address entries 105
- Overview 107
- Management module switchover 108
- Switchover implications 109
- Management sessions 110
- Syslog and SNMP traps 110
- MAC address changes 110
- Status LED 114
- Software 114
- Maintaining the Hardware 117
- Replacing a management module 118
- 1 Management module 121
- 1Switch Fabric module 123
- Replacing an interface module 124
- Removing an interface module 125
- Brocade# disable module 3 128
- 1Interface module 128
- Brocade# enable module 3 129
- Brocade# disable module 1 129
- 1 Connector slots 130
- FIGURE 54 POE daughter card 131
- 24-port Gig Copper + PoE 132
- 1Bail Latch 133
- Cabling a fiber optic module 134
- Removing an AC power supply 135
- 1 Latch retaining screw 136
- 2 Latch retaining screw 136
- Removing a DC power supply 137
- DC IN DC OUT ALM 139
- Installing a new power supply 140
- Tighten the retaining screw 142
- EJECT SYS 143
- EJECT POE 143
- 1Cord retainer 144
- 2DC power 147
- Verifying proper operation 148
- Chassis front Chassis rear 150
- Fan Tray 151
- Fan Tray Latch 151
- Fan Assembly 152
- Filter Retainer 153
- Grab-strap 153
- Hardware Specifications 155
- Description Range 156
- FSX 1600 157
- Regulatory compliance 158
- Maximum power consumption 159
- Power source interruptions 160
- Pinouts and signalling 160
- Serial (console) port pinouts 161
- Chassis specifications 162
- Cable specifications 163
- Power cords 164
- Power supply specifications 165
- Electrical specifications 166
- Input connector and plug 167
- Description Certifications 169
- Safety warnings 170
- Regulatory Statements 171
- BSMI statement (Taiwan) 173
- Caution and Danger Notices 175
- Cautions 176
Related products and manuals for Network switches Brocade Communications Systems Brocade Superx Series
(330 pages)© 2020, manymanuals.com. All rights reserved. | 0.489 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals