Brocade Communications Systems 4900 Service Manual Page 222
- Page / 266
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
200 Web Tools Administrator’s Guide
Publication Number: 53-1000435-01
Configuring link cost
16
To configure the IOD setting
1. Open the Switch Administration window as described on page 31.
2. Click the Routing tab.
3. Click On in the In-Order Delivery (IOD) area to force in-order frame delivery across topology
changes or click Off to restore out-of-order frame delivery across topology changes.
4. Click Apply.
Configuring link cost
This section describes how to set the cost of an interswitch link (ISL). The cost of a link is a
dimensionless positive number. The fabric shortest path first (FSPF) protocol compares the cost of
various paths between a source switch and a destination switch by adding the costs of all the ISLs
along each path. FSPF chooses the path with minimum cost. If multiple paths exist with the same
minimum cost, FSPF employs load sharing over these paths.
Every ISL has a default cost that is inversely proportional to its bandwidth. For a 1-Gbit/sec ISL, the
default cost is 1000. For a 2-Gbit/sec ISL, the default cost is 500.
Use this procedure to set a non-default, “static” cost for any port.
When you configure link cost for a Brocade 24000 or 48000 configured for two logical switches, it
is on a logical-switch basis. This means that for each logical switch, you configure link cost
individually.
To configure the link cost for a port
1. Open the Switch Administration window as described on page 31.
2. Click the Routing tab.
3. This step is switch-specific:
For Brocade 24000 and 48000 directors, click the slot number of the logical switch under Link
Cost in the navigation tree.
For Brocade 200E, 3250, 3850, 3900, 4012, 4016, 4018, 4020, 4024, 4100, 4900, 5000,
and 7500 switches, click Link Cost in the navigation tree.
4. Double-click in the row in the Cost column that corresponds to the appropriate port.
5. Type the link cost.
Valid values for link cost are from 1 through 65535. Setting the value to 0 sets the link cost to
the default value for that port.
6. Click Apply.
- Web Tools 1
- Document History 3
- Contents 5
- Chapter 5 Managing Your Ports 7
- Chapter 16 Routing Traffic 10
- Chapter 19 Limitations 11
- About This Document 13
- What’s new in this document 15
- Document conventions 16
- Additional information 17
- OPTIONAL BROCADE FEATURES 19
- Getting technical help 20
- Document feedback 21
- Introducing Web Tools 23
- Configuring Internet Explorer 24
- Configuring the Java plug-in 26
- FIGURE 2 Java Control Panel 27
- Launching Web Tools 30
- Administrative domains 31
- ADMIN DOMAINS AND LOGIN 32
- Role-Based access control 33
- Session management 34
- FIGURE 7 Login dialog box 35
- LOGGING OUT 36
- REQUIREMENTS FOR IPV6 SUPPORT 37
- Using the Web Tools Interface 39
- FIGURE 10 Switch Explorer 40
- FABRIC TREE 41
- ADMIN DOMAIN CONTEXT 42
- SWITCH VIEW BUTTONS 43
- SWITCH VIEW 43
- Port representations 43
- Displaying tool tips 44
- Refresh rates 46
- DISABLED FUNCTIONALITY 48
- Managing Fabrics and Switches 51
- Opening the telnet window 53
- FIGURE 16 Network tab 54
- Filtering IP Addresses 56
- Managing blades 56
- ENABLE OR DISABLE A BLADE 57
- Set IP address 57
- View IP addresses 58
- Configuring a switch 59
- CHANGING THE SWITCH DOMAIN ID 60
- Rebooting the switch 61
- Managing licensed features 65
- FIGURE 22 License tab 66
- INITIATING A CP FAILOVER 69
- Monitoring events 70
- DISPLAYING FABRIC EVENTS 71
- DISPLAYING SWITCH EVENTS 72
- FIGURE 29 Name Server window 76
- Maintaining configurations 79
- RESTORING A CONFIGURATION 81
- Managing Your Ports 85
- Configuring ports 89
- Allowed Port Types 90
- Long distance mode 91
- FC Fastwrite 91
- CONFIGURING FCIP PORTS 91
- Assigning a name to a port 92
- Enabling and disabling a port 93
- Activating ports 95
- Swapping port index 97
- Administering ISL Trunking 99
- • Master port 100
- • Member ports 100
- In this chapter 103
- About administrative domains 103
- USER-DEFINED ADMIN DOMAINS 104
- SYSTEM-DEFINED ADMIN DOMAINS 104
- AD255 or physical fabric 104
- ADMIN DOMAIN MEMBERSHIP 105
- Using the Admin Domain window 106
- REFRESHING FABRIC INFORMATION 109
- FIGURE 44 Summary view 112
- ADDING AND REMOVING MEMBERS 113
- RENAMING ADMIN DOMAINS 115
- DELETING ADMIN DOMAINS 115
- Administering Zoning 117
- Zoning and admin domains 118
- Configuring zoning 118
- ATTENTION 120
- SAVING LOCAL ZONING CHANGES 122
- ZONING VIEWS 123
- Managing zone aliases 124
- RENAMING ZONE ALIASES 125
- DELETING ZONE ALIASES 125
- Managing zones 126
- RENAMING ZONES 127
- Managing zone configurations 128
- CREATING ZONE CONFIGURATIONS 129
- RENAMING ZONE CONFIGURATIONS 130
- COPYING ZONE CONFIGURATIONS 131
- DELETING ZONE CONFIGURATIONS 131
- ENABLING ZONE CONFIGURATIONS 131
- DISABLING ZONE CONFIGURATIONS 132
- Managing the zoning database 136
- SEARCHING FOR ZONE MEMBERS 137
- CLEARING THE ZONING DATABASE 138
- USING ZONING WIZARDS 138
- Replacing offline devices 140
- Defining device aliases 140
- Best practices for zoning 141
- Monitoring Performance 143
- PREDEFINED PERFORMANCE GRAPHS 144
- Graph Type Displays 145
- USER-DEFINED GRAPHS 147
- CANVAS CONFIGURATIONS 148
- • Switch Percent Utilization 149
- • Port Snapshot Error 149
- CREATING SCSI COMMAND GRAPHS 153
- Managing performance graphs 154
- ADDING GRAPHS TO A CANVAS 155
- PRINTING GRAPHS 155
- MODIFYING GRAPHS 156
- About fibre channel routing 157
- MCDATA INTEROPERABILITY 158
- Setting up FC-FC routing 159
- • Brocade 7500 switch 160
- • Rename an EX_Port 162
- VIEWING LSAN DEVICES 165
- Managing trace dumps 169
- HOW A TRACE DUMP IS USED 170
- Displaying switch information 171
- FIGURE 65 Fan States window 172
- FIGURE 67 Power Status window 174
- - Customize the report 175
- Interpreting port LEDs 176
- PORT ICON COLORS 177
- LED REPRESENTATIONS 177
- BROCADE 48000 DIRECTOR LEDS 178
- Administering Fabric Watch 179
- CONFIGURING THRESHOLD TRAITS 181
- CONFIGURING THRESHOLD ALARMS 183
- Configuring alarms for FRUs 184
- DISPLAYING ALARMS 185
- - Auto-Negotiation 190
- Required? 191
- Supported platforms for iSCSI 193
- About the iSCSI service 193
- FIGURE 76 Search screen 194
- TERMINOLOGY 195
- SAVING CHANGES 196
- ACTIVATING THE ISCSI FEATURE 198
- CONFIGURING THE IP INTERFACE 198
- FIGURE 78 iSCSI Port tab 199
- VIEWING ISCSI INITIATORS 203
- MANAGING DISCOVERY DOMAINS 204
- About Discovery Domains (DD) 204
- FIGURE 85 Create DD wizard 205
- CONFIGURING CHAP 207
- FIGURE 87 CHAP tab 208
- Using the Access Gateway 213
- Displaying the port mapping 214
- Configuring port maps 215
- Converting ports 216
- Routing Traffic 219
- Displaying FSPF routing 220
- Configuring link cost 222
- Role Permissions 224
- FIGURE 92 User tab 225
- CHANGING ACCOUNT PARAMETERS 227
- MAINTAINING PASSWORDS 228
- Configuring SNMP 233
- CONFIGURING SNMP INFORMATION 234
- Managing RADIUS service 235
- FIGURE 98 AAA Service tab 237
- MODIFYING THE RADIUS SERVER 238
- REMOVING A RADIUS SERVER 239
- About FICON CUP fabrics 241
- Configuring FMS parameters 244
- USA/Canada -- 00037 245
- - Mode Register 246
- - Switch enable/disable 246
- - Switch name change 246
- Limitations 253
- General Web Tools limitations 254
- Platform-specific limitations 257
- Numerics 259
Related products and manuals for Network switches Brocade Communications Systems 4900
Network switches Brocade Communications Systems AA979A - StorageWorks SAN Switch 2/8V User's Guide
(46 pages)
(46 pages)
Network switches Brocade Communications Systems AA979A - StorageWorks SAN Switch 2/8V User Manual
(11 pages)
(11 pages)
Network switches Brocade Communications Systems StorageWorks 4/32B - SAN Switch Service Manual
(26 pages)
(26 pages)
© 2020, manymanuals.com. All rights reserved. | 0.925 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals