Brocade Communications Systems ServerIron ADX 12.4.00 Service Manual Page 172
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ServerIron ADX Firewall Load Balancing Guide 161
53-1002436-01
Displaying firewall path information
7
DRAFT: BROCADE CONFIDENTIAL
Table 8 describes the information displayed by the show server fw-path command.
TABLE 8 FWLB path information
Field Description
General Information
Number of Paths Configured The number of firewall and router paths configured in the group.
Number of Fwall Paths
preferred
Number of Router Paths
preferred
Target-ip (IPv4)
Target-ipv6
The IP address of the device at the other end of the path. Generally, this other
device is another ServerIron.
Next-hop-ip (IPv4)
Next-hop-ipv6
The IP address of the device at the next hop to the target IP. Usually, this is the
IP interface on the firewall that is connected to this ServerIron.
Port The ServerIron port for this path. This is the port connected to the firewall.
Path The path ID.
Status The status of the path, which can be one of the following:
• 0 – The path is down.
• 1 – The path is up.
Tx Indicates the state of the transmit side of the path. The state can be one of the
following:
• 0 – The transmit side is down.
• 1 – The transmit side is up.
Rx Indicates the state of the receive side of the path. The state can be one of the
following:
• 0 – The receive side is down.
• 1 – The receive side is up.
State The state of the other end of the path.
5 – The ServerIron ADX at the other end of the path is in active mode for the
firewall group.
NOTE: This field applies only to IronClad FWLB. If the ServerIron ADX is not
configured with another ServerIron ADX as the active or backup
ServerIron ADX for IronClad FWLB, the state is always 0.
Zone
Partner known Indicates whether this ServerIron ADX can see (has Layer 2 connectivity with)
the other ServerIron ADX in the pair.
This field can have one of the following values:
• No – This ServerIron ADX does not have Layer 2 connectivity with its
partner. Generally, this indicates that the link is down.
• Yes – This ServerIron ADX has Layer 2 connectivity with its partner.
NOTE: This field applies only to the other ServerIron ADX in an active-standby
configuration for IronClad FWLB.
port
sync-state
FW Partner MAC valid
FW Partner MAC
- ServerIron ADX 1
- Document History 2
- Contents 3
- About This Document 8
- Document conventions 9
- Notice to the reader 10
- Related publications 11
- ServerIron FWLB Overview 12
- Firewall environments 14
- Load balancing paths 15
- Firewall selection 17
- Hashing mechanism 17
- Stateful FWLB 18
- Health checks 18
- Path health checks 19
- Application health checks 19
- Firewall health check debug 21
- Basic FWLB topology 22
- HA FWLB topology 23
- Failover 24
- Router paths 24
- Multizone FWLB topology 25
- FWLB configuration limits 26
- Configuring Basic FWLB 28
- IPv4 Firewall-1 37
- IPv4 Firewall-2 37
- External 40
- Internal 40
- Firewall-2 42
- Firewall-1 42
- Configuring HA FWLB 48
- Session limits 49
- Session aging 49
- Task Reference 52
- Configuring the firewall port 53
- Configuring the partner port 54
- Configuring the router port 55
- Configuring the firewalls 55
- Adding the firewalls 55
- Connection rate control 57
- Complete CLI example 62
- HA FWLB with VRRP 73
- Usage notes 78
- Configuring Multizone FWLB 82
- Zone 3Zone 2 84
- Zone1-SI(config)# no span 85
- Failover algorithm 92
- Commands on Zone1-SI-A zone 1 92
- DRAFT: BROCADE CONFIDENTIAL 100
- 53-1002436-01 102
- SI-A SI-A 104
- In this chapter 124
- NAT firewalls 124
- Extra firewall method 129
- Access policy method 130
- Specifying the partner port 134
- Specifying the router ports 134
- Configuring FWLB and SLB 146
- Configuring SLB-to-FWLB 148
- Configuring the real servers 149
- Enabling SLB-to-FWLB 150
- Configuring FWLB-to-SLB 152
- Enabling FWLB-to-SLB 154
- FWLB configuration overview 166
- TCP/UDP port statistics 169
- FWLB path information 172
- Field Description 173
- • 6 – TCP 174
- • 17 – UDP 174
- In this appendix 176
- FWLB selection algorithms 182
- Configuration guidelines 186
- Denying FWLB 187
Related products and manuals for Network switches Brocade Communications Systems ServerIron ADX 12.4.00
(12 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.244 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals