Brocade Communications Systems ServerIron ADX 12.4.00 Service Manual Page 30
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ServerIron ADX Firewall Load Balancing Guide 19
53-1002436-01
Configuration guidelines
2
DRAFT: BROCADE CONFIDENTIAL
Commands for ServerIron ADX B (internal)
ServerIron ADX(config)# server fw-name FW1-IPout 209.157.23.1
ServerIron ADX(config-rs-FW1-IPout)# exit
ServerIron ADX(config)# server fw-name FW2-IPout 209.157.23.2
ServerIron ADX(config-rs-FW2-IPout)# exit
ServerIron ADX(config)# server fw-group 2
ServerIron ADX(config-fw-2)# fw-name FW1-IPout
ServerIron ADX(config-fw-2)# fw-name FW2-IPout
Syntax: [no] server fw-name <name> <ip-addr>
NOTE
When you add a firewall name, the CLI level changes to the firewall level. This level is used when
you configure stateful FWLB.
Syntax: (IPv4) server fw-group 2
These commands change the CLI to the firewall group configuration level. The IPv4 firewall group
number is 2. Only one IPv4 firewall group is supported.
Syntax: [no] fw-name <string>
Adds a configured firewall to the firewall group.
IPv6 example for defining a firewall and adding them to a firewall group
To define the firewalls shown in Figure 2 on page 11 and add them to a firewall group, use the
following method.
Commands for ServerIron ADX A (external)
ServerIron ADX(config)# server fw-name ip6fw1 1112::2
ServerIron ADX(config-rs-ip6fw1)# end
ServerIron ADX(config)# server fw-name ip6fw2 1112::3
ServerIron ADX(config-rs-ip6fw2)# end
ServerIron ADX(config)# server fw-group 4 ipv6
ServerIron ADX(config-fw-4)# fw-name ip6fw1
ServerIron ADX(config-fw-4)# fw-name ip6fw2
Commands for ServerIron ADX B (internal)
ServerIron ADX(config)# server fw-name ip6fw1 1113::2
ServerIron ADX(config-rs-ip6fw1)# end
ServerIron ADX(config)# server fw-name ip6fw2 1113::3
ServerIron ADX(config-rs-ip6fw2)# end
ServerIron ADX(config)# server fw-group 4 ipv6
ServerIron ADX(config-fw-4)# fw-name ip6fw1
ServerIron ADX(config-fw-4)# fw-name ip6fw2
Syntax: [no] server fw-name <name> <ipv6-addr>
NOTE
When you add a firewall name, the CLI level changes to the firewall level. This level is used when
you configure stateful FWLB.
Syntax: (IPv6) [no] server fw-group 4 ipv6
These commands change the CLI to the firewall group configuration level. The IPv6 firewall group
number is 4. Only one IPv6 firewall group is supported.
- ServerIron ADX 1
- Document History 2
- Contents 3
- About This Document 8
- Document conventions 9
- Notice to the reader 10
- Related publications 11
- ServerIron FWLB Overview 12
- Firewall environments 14
- Load balancing paths 15
- Firewall selection 17
- Hashing mechanism 17
- Stateful FWLB 18
- Health checks 18
- Path health checks 19
- Application health checks 19
- Firewall health check debug 21
- Basic FWLB topology 22
- HA FWLB topology 23
- Failover 24
- Router paths 24
- Multizone FWLB topology 25
- FWLB configuration limits 26
- Configuring Basic FWLB 28
- IPv4 Firewall-1 37
- IPv4 Firewall-2 37
- External 40
- Internal 40
- Firewall-2 42
- Firewall-1 42
- Configuring HA FWLB 48
- Session limits 49
- Session aging 49
- Task Reference 52
- Configuring the firewall port 53
- Configuring the partner port 54
- Configuring the router port 55
- Configuring the firewalls 55
- Adding the firewalls 55
- Connection rate control 57
- Complete CLI example 62
- HA FWLB with VRRP 73
- Usage notes 78
- Configuring Multizone FWLB 82
- Zone 3Zone 2 84
- Zone1-SI(config)# no span 85
- Failover algorithm 92
- Commands on Zone1-SI-A zone 1 92
- DRAFT: BROCADE CONFIDENTIAL 100
- 53-1002436-01 102
- SI-A SI-A 104
- In this chapter 124
- NAT firewalls 124
- Extra firewall method 129
- Access policy method 130
- Specifying the partner port 134
- Specifying the router ports 134
- Configuring FWLB and SLB 146
- Configuring SLB-to-FWLB 148
- Configuring the real servers 149
- Enabling SLB-to-FWLB 150
- Configuring FWLB-to-SLB 152
- Enabling FWLB-to-SLB 154
- FWLB configuration overview 166
- TCP/UDP port statistics 169
- FWLB path information 172
- Field Description 173
- • 6 – TCP 174
- • 17 – UDP 174
- In this appendix 176
- FWLB selection algorithms 182
- Configuration guidelines 186
- Denying FWLB 187
Related products and manuals for Network switches Brocade Communications Systems ServerIron ADX 12.4.00
(12 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.441 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals