Brocade Communications Systems Mobility 7131 Series Service Manual Page 352
- Page / 520
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
340 Brocade Mobility 7131 Access Point Product Reference Guide
53-1002517-01
8
Client Bridge Signal Monitor : enable
Client Bridge Signal Threshold : 65
Client Bridge Signal Delta : 10
Mesh Wired Peer Detection Mode : disable
Mesh Auto Single Connection Mode : disable
Dot11 Auth Algorithm : open-system-only
DSCP QOS Mappings:
DSCP value : Wireless Traffic ID (WMM
AC)
0 1 2 3 4 5 6 7 : 0 (best-effort)
8 9 10 11 12 13 14 15 : 1 (background)
16 17 18 19 20 21 22 23 : 2 (background)
24 25 26 27 28 29 30 31 : 3 (best-effort)
32 33 34 35 36 37 38 39 : 4 (video)
40 41 42 43 44 45 47 : 5 (video)
46 48 49 50 51 52 53 54 55 : 6 (voice)
56 57 58 59 60 61 62 63 : 7 (voice)
For information on configuring the Radio Configuration options available to the access point using
the applet (GUI), see Setting the Radio Configuration for a WLAN on page 5-161.
br7131>admin(network.wireless.radio)>set
Description:
Sets the Mobility 7131 Access Point’s radio configuration and defines the RF band of operation.
Syntax:
set radio-config <mode> Sets the radio configuration. The options available differ depending on the single,
dual or three radio configuration deployed (see examples below).
max-mus <mus> Defines the maximum number of MUs assigned to the specified radio (idx 1 or 2).
The range can be defined between 0 and 127. This command does not apply to
single radio access points.
mesh-auto-mode <radio> <mode> Enables or disables the Auto-Mesh Mode feature. When enabled, the Auto-Mesh
Mode feature enables an AP to become a Base Bridge and a Client Bridge
simultaneously. This feature enables the AP to be a Client Bridge and connect to a
Base Bridge while serving as a Base Bridge for other Client Bridge APs.
mesh-base <mode> Enables or disables base bridge mode.
mesh-max <clients> Sets the maximum number of wireless bridge clients.
mesh-client <mode> Enables or disables client bridge mode.
mesh-roaming-client <mode> Enables or disables the mesh roaming client mode. For information on the Mesh
Roaming Client feature, see Mesh Roaming Client on page 1-9.
mesh-timeout <mode> Sets the client bridge link timeout.
mesh-wlan <name> Defines the client bridge WLAN name.
mesh-associations <radio>
<associations>
Sets the maximum client bridge associations per radio. Sets a value in the range
1-3 per radio.
mesh-monitor <radio> <mode> Enables or diables mesh link monitoring on client bridge per radio.
- Brocade Mobility 7131 1
- Access Point 1
- Document History 2
- Contents 3
- Chapter 3 Getting Started 5
- Chapter 5 Network Management 6
- Chapter 8 CLI Reference 8
- Chapter 10 Adaptive AP 8
- Chapter B Usage Scenarios 9
- 53-1002517-01 10
- About This Guide 11
- Related publications 12
- Getting technical help 12
- Introduction 13
- New Features 14
- Hotspot Customization 15
- WAN Failover 15
- Proxy ARP Support 16
- Multi Cipher Support 16
- Dynamic Chain Selection 17
- Dedicated Sensor Support 17
- LED Disable 17
- Feature Overview 18
- 802.11n Support 19
- Sensor Support 19
- Mesh Roaming Client 21
- Separate LAN and WAN Ports 21
- Multiple Mounting Options 22
- Sixteen Configurable WLANs 22
- • Kerberos Authentication 23
- • EAP Authentication 23
- • WEP Encryption 23
- Kerberos Authentication 24
- EAP Authentication 24
- WEP Encryption 25
- KeyGuard Encryption 25
- Firewall Security 26
- VPN Tunnels 26
- VLAN Support 27
- Updatable Firmware 27
- Power-over-Ethernet Support 28
- MU-MU Transmission Disallow 28
- Voice Prioritization 29
- Support for CAM and PSP MUs 29
- Statistical Displays 29
- DHCP Support 30
- Transmit Power Control 30
- Mesh Networking 31
- Additional LAN Subnet 31
- Hotspot Support 32
- Manual Date and Time Settings 33
- Dynamic DNS 33
- Auto Negotiation 33
- Adaptive AP 33
- Rogue AP Enhancements 34
- QBSS Support 34
- Triple Radio Support 34
- IP Filtering 35
- MU Rate Limiting 35
- Per Radio MU Limit 35
- Power Setting Configuration 36
- AMSDU Transmission Support 36
- IPSec VPN Support 36
- Theory of Operations 37
- MAC Layer Bridging 38
- Media Types 39
- MU Association Process 39
- Operating Modes 40
- Management Access Options 41
- MAC Address Assignment 41
- Hardware Installation 43
- Package Contents 44
- Access Point Placement 45
- Power Options 47
- Power Injector System 47
- Cabling the Power Injector 49
- Mobility 7131N Access Point 50
- • Light pipe 55
- • Badge for light pipe 55
- • Decal for badge 55
- • Security cable (optional) 55
- LED Indicators 57
- Dual Radio (2.4/5 GHz) LEDs 59
- Single Radio 2.4 GHz LEDs 60
- Single Radio 5 GHz LEDs 60
- Setting Up MUs 61
- Getting Started 63
- Basic Device Configuration 65
- Configuring Device Settings 67
- Testing Connectivity 76
- Where to Go from Here? 76
- System Configuration 79
- Configuring Power Settings 82
- Available Power 83
- Power 2.4 GHz 84
- Maximum Transmit 84
- Power 5 GHz 84
- Power 5 GH 85
- Adaptive AP Setup 87
- Configuring Data Access 89
- LAN1, LAN2 or WAN interfaces: 90
- Importing a CA Certificate 93
- Ensure the 97
- Configuring SNMP Settings 99
- Feature MIB Feature MIB 100
- Mobility 7131 Access Point 103
- Mobility 7131 Access 103
- • Enabling SNMP Traps 104
- Enabling SNMP Traps 105
- Configuring LLDP Settings 111
- Mobility 7131 114
- Logging Configuration 115
- Updating Device Firmware 121
- Network Management 127
- Configuring VLAN Support 130
- Configuring WAN Settings 139
- • Novatel Merlin 870 143
- Configuring Port Forwarding 146
- Configuring Dynamic DNS 147
- Customizing a Hotspot Display 168
- (mutually exclusive) 173
- Configuring MU Rate Limiting 188
- Configuring Router Settings 190
- Setting the RIP Configuration 191
- Configuring IP Filtering 193
- Creating a Global Filter 196
- LAN and WLAN filter policies 197
- Assessing IP Filter Stats 199
- In this chapter 201
- Configuring Security Options 202
- Setting Passwords 202
- Mobility 205
- 7131 Access Point 205
- Configuring WEP Encryption 211
- Configuring Firewall Settings 222
- Available Protocols 226
- Configuring VPN Tunnels 228
- Configuring Auto Key Settings 236
- Configuring IKE Key Settings 238
- VPN Configuration - Example 241
- Viewing VPN Status 242
- Displaying Rogue AP Details 250
- Configuring the Radius Server 253
- Group Member 256
- Attribute 256
- Mapping Users to Groups 259
- Monitoring Statistics 265
- Viewing LAN Statistics 268
- Viewing Wireless Statistics 273
- Viewing WLAN Statistics 274
- Viewing Radio Statistics 279
- Retry Histogram 282
- Viewing MU Statistics Summary 283
- Viewing MU Details 284
- Pinging Individual MUs 286
- MU Authentication Statistics 286
- CLI Reference 293
- Admin and Common Commands 294
- Description: 295
- Syntax: 295
- Example: 295
- Network Commands 298
- Network Type Filter Commands 310
- Network WAN Commands 313
- Network WAN NAT Commands 315
- Related Commands: 318
- Network Wireless Commands 330
- Network ACL Commands 348
- GHz].advanced)>show 358
- GHz].advanced)>set 359
- GHz].mesh)>show 360
- GHz].mesh)>delete 361
- Descripton: 370
- Network Rogue-AP Commands 373
- Network Firewall Commands 380
- Network Router Commands 383
- Network IP Filter Commands 387
- System Commands 390
- Power Setup Commands 394
- Adaptive AP Setup Commands 395
- LLDP Commands 398
- System Access Commands 399
- Description: ) 402
- System SNMP Commands 407
- System SNMP Traps Commands 410
- System User Database Commands 415
- System Radius Commands 421
- Description: set 425
- zone-list 434
- System Log Commands 435
- Firmware Update Commands 443
- Statistics Commands 445
- Configuring Mesh Networking 455
- Spanning Tree Protocol (STP) 457
- Defining the Mesh Topology 457
- Normal Operation 458
- Configuring AP#1: 470
- Configuring AP#2 474
- Configuring AP#3 474
- Configuring AP#1 476
- Where to Go From Here 484
- Adaptive AP Management 484
- Licensing 484
- Switch Discovery 484
- Auto Discovery using DHCP 485
- Manual Adoption Configuration 485
- Adaptive AP WLAN Topology 486
- Configuration Updates 486
- Adaptive AP Switch Failure 487
- Adaptive Mesh Support 487
- Extended WLANs Only 488
- Independent WLANs Only 489
- Adaptive AP Configuration 491
- Option Data Type Value 492
- Switch Configuration 493
- IPSec and Independent WLAN 496
- Technical Specifications 501
- Electrical Characteristics 502
- Country Codes 503
- Country Code Country Code 504
- Usage Scenarios 507
- Code Data type 508
- • 1 TFTP Server 509
- DHCP Priorities 510
- BootP Options 511
- • Sends a true BootP request 512
- BootP Priorities 513
- • 1 Cisco VPN device 517
Related products and manuals for WLAN access points Brocade Communications Systems Mobility 7131 Series
(65 pages)© 2020, manymanuals.com. All rights reserved. | 2.320 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals