Brocade Communications Systems Mobility 7131 Series Service Manual Page 413
- Page / 520
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Brocade Mobility 7131 Access Point Product Reference Guide 401
53-1002517-01
8
For information on configuring SNMP traps using the applet (GUI), see Configuring Specific SNMP
Traps on page 4-95.
br7131>admin(system.snmp.traps)>add
Description:
Adds SNMP trap entries.
Syntax:
Example:
admin(system.snmp.traps)>add v1v2 203.223.24.2 333 mycomm v1
admin(system.snmp.traps)>list v1v2c
----------------------------------------------------------------------
index dest ip dest port community version
----------------------------------------------------------------------
1 203.223.24.2 333 mycomm v1
admin(system.snmp.traps)>
add v3 201.232.24.33 555 BigBoss none md5
admin(system.snmp.traps)>list v3 all
index : 1
destination ip : 201.232.24.33
destination port : 555
min-pkt <pkt> Sets the minimum number of packets required for rate traps to
fire (
1-65535).
dyndns-update
enable/disab
le
Enables/disables dyndns update trap.
wlan-kerb-auth-fail
enable/disab
le
Enables/disables the WLAN Kerberos authentication trap.
wwan-event
enable/disab
le
Enables/disables the WWAN event trap.
all
enable/disab
le
Enables/disables each trap.
health-check-event
enable/disab
le
Enables/disables health check event trap.
add v1v2 <ip> <port> <comm>
<ver>
Adds an entry to the SNMP v1/v2 access list with the destination IP address set to <ip>, the destination UDP port set to
<port>, the community string set to <comm> (1 to 31 characters), and the SNMP version set to <ver>.
v3 <ip> <port> <user> <sec> <auth> <pass1> <priv> <pass2>
Adds an entry to the SNMP v3 access list with the destination IP address set to <ip>, the destination UDP port set to
<port>, the username set to <user> (1 to 31 characters), and the authentication type set to one of
none, auth, or
auth/priv.
The following parameters must be specified if <sec> is not
none:
Authentication type <auth> set to
md5 or sha1
Authentication password <pass1> (8 to 31 chars)
The following parameters must be specified if <sec> is set to
auth/priv:
Privacy algorithm set to
des or aes
Privacy password <pass2> (8 to 31 chars)
- Brocade Mobility 7131 1
- Access Point 1
- Document History 2
- Contents 3
- Chapter 3 Getting Started 5
- Chapter 5 Network Management 6
- Chapter 8 CLI Reference 8
- Chapter 10 Adaptive AP 8
- Chapter B Usage Scenarios 9
- 53-1002517-01 10
- About This Guide 11
- Related publications 12
- Getting technical help 12
- Introduction 13
- New Features 14
- Hotspot Customization 15
- WAN Failover 15
- Proxy ARP Support 16
- Multi Cipher Support 16
- Dynamic Chain Selection 17
- Dedicated Sensor Support 17
- LED Disable 17
- Feature Overview 18
- 802.11n Support 19
- Sensor Support 19
- Mesh Roaming Client 21
- Separate LAN and WAN Ports 21
- Multiple Mounting Options 22
- Sixteen Configurable WLANs 22
- • Kerberos Authentication 23
- • EAP Authentication 23
- • WEP Encryption 23
- Kerberos Authentication 24
- EAP Authentication 24
- WEP Encryption 25
- KeyGuard Encryption 25
- Firewall Security 26
- VPN Tunnels 26
- VLAN Support 27
- Updatable Firmware 27
- Power-over-Ethernet Support 28
- MU-MU Transmission Disallow 28
- Voice Prioritization 29
- Support for CAM and PSP MUs 29
- Statistical Displays 29
- DHCP Support 30
- Transmit Power Control 30
- Mesh Networking 31
- Additional LAN Subnet 31
- Hotspot Support 32
- Manual Date and Time Settings 33
- Dynamic DNS 33
- Auto Negotiation 33
- Adaptive AP 33
- Rogue AP Enhancements 34
- QBSS Support 34
- Triple Radio Support 34
- IP Filtering 35
- MU Rate Limiting 35
- Per Radio MU Limit 35
- Power Setting Configuration 36
- AMSDU Transmission Support 36
- IPSec VPN Support 36
- Theory of Operations 37
- MAC Layer Bridging 38
- Media Types 39
- MU Association Process 39
- Operating Modes 40
- Management Access Options 41
- MAC Address Assignment 41
- Hardware Installation 43
- Package Contents 44
- Access Point Placement 45
- Power Options 47
- Power Injector System 47
- Cabling the Power Injector 49
- Mobility 7131N Access Point 50
- • Light pipe 55
- • Badge for light pipe 55
- • Decal for badge 55
- • Security cable (optional) 55
- LED Indicators 57
- Dual Radio (2.4/5 GHz) LEDs 59
- Single Radio 2.4 GHz LEDs 60
- Single Radio 5 GHz LEDs 60
- Setting Up MUs 61
- Getting Started 63
- Basic Device Configuration 65
- Configuring Device Settings 67
- Testing Connectivity 76
- Where to Go from Here? 76
- System Configuration 79
- Configuring Power Settings 82
- Available Power 83
- Power 2.4 GHz 84
- Maximum Transmit 84
- Power 5 GHz 84
- Power 5 GH 85
- Adaptive AP Setup 87
- Configuring Data Access 89
- LAN1, LAN2 or WAN interfaces: 90
- Importing a CA Certificate 93
- Ensure the 97
- Configuring SNMP Settings 99
- Feature MIB Feature MIB 100
- Mobility 7131 Access Point 103
- Mobility 7131 Access 103
- • Enabling SNMP Traps 104
- Enabling SNMP Traps 105
- Configuring LLDP Settings 111
- Mobility 7131 114
- Logging Configuration 115
- Updating Device Firmware 121
- Network Management 127
- Configuring VLAN Support 130
- Configuring WAN Settings 139
- • Novatel Merlin 870 143
- Configuring Port Forwarding 146
- Configuring Dynamic DNS 147
- Customizing a Hotspot Display 168
- (mutually exclusive) 173
- Configuring MU Rate Limiting 188
- Configuring Router Settings 190
- Setting the RIP Configuration 191
- Configuring IP Filtering 193
- Creating a Global Filter 196
- LAN and WLAN filter policies 197
- Assessing IP Filter Stats 199
- In this chapter 201
- Configuring Security Options 202
- Setting Passwords 202
- Mobility 205
- 7131 Access Point 205
- Configuring WEP Encryption 211
- Configuring Firewall Settings 222
- Available Protocols 226
- Configuring VPN Tunnels 228
- Configuring Auto Key Settings 236
- Configuring IKE Key Settings 238
- VPN Configuration - Example 241
- Viewing VPN Status 242
- Displaying Rogue AP Details 250
- Configuring the Radius Server 253
- Group Member 256
- Attribute 256
- Mapping Users to Groups 259
- Monitoring Statistics 265
- Viewing LAN Statistics 268
- Viewing Wireless Statistics 273
- Viewing WLAN Statistics 274
- Viewing Radio Statistics 279
- Retry Histogram 282
- Viewing MU Statistics Summary 283
- Viewing MU Details 284
- Pinging Individual MUs 286
- MU Authentication Statistics 286
- CLI Reference 293
- Admin and Common Commands 294
- Description: 295
- Syntax: 295
- Example: 295
- Network Commands 298
- Network Type Filter Commands 310
- Network WAN Commands 313
- Network WAN NAT Commands 315
- Related Commands: 318
- Network Wireless Commands 330
- Network ACL Commands 348
- GHz].advanced)>show 358
- GHz].advanced)>set 359
- GHz].mesh)>show 360
- GHz].mesh)>delete 361
- Descripton: 370
- Network Rogue-AP Commands 373
- Network Firewall Commands 380
- Network Router Commands 383
- Network IP Filter Commands 387
- System Commands 390
- Power Setup Commands 394
- Adaptive AP Setup Commands 395
- LLDP Commands 398
- System Access Commands 399
- Description: ) 402
- System SNMP Commands 407
- System SNMP Traps Commands 410
- System User Database Commands 415
- System Radius Commands 421
- Description: set 425
- zone-list 434
- System Log Commands 435
- Firmware Update Commands 443
- Statistics Commands 445
- Configuring Mesh Networking 455
- Spanning Tree Protocol (STP) 457
- Defining the Mesh Topology 457
- Normal Operation 458
- Configuring AP#1: 470
- Configuring AP#2 474
- Configuring AP#3 474
- Configuring AP#1 476
- Where to Go From Here 484
- Adaptive AP Management 484
- Licensing 484
- Switch Discovery 484
- Auto Discovery using DHCP 485
- Manual Adoption Configuration 485
- Adaptive AP WLAN Topology 486
- Configuration Updates 486
- Adaptive AP Switch Failure 487
- Adaptive Mesh Support 487
- Extended WLANs Only 488
- Independent WLANs Only 489
- Adaptive AP Configuration 491
- Option Data Type Value 492
- Switch Configuration 493
- IPSec and Independent WLAN 496
- Technical Specifications 501
- Electrical Characteristics 502
- Country Codes 503
- Country Code Country Code 504
- Usage Scenarios 507
- Code Data type 508
- • 1 TFTP Server 509
- DHCP Priorities 510
- BootP Options 511
- • Sends a true BootP request 512
- BootP Priorities 513
- • 1 Cisco VPN device 517
Related products and manuals for WLAN access points Brocade Communications Systems Mobility 7131 Series
(65 pages)© 2020, manymanuals.com. All rights reserved. | 1.971 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals