Brocade Communications Systems NetIron CER Series Installation Guide Page 92
- Page / 120
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Verifying proper operation
To verify the proper operation of the power supply after power on, you can observe the LEDs on the
power supply.
After the Brocade device powers on, you can observe the LEDs on the front of the device to verify that
it initialized successfully. There is a single LED on the power supply which should be steady green
when the power supply is receiving power and under normal operation.Table 1 outlines the LEDs, the
desired state of each LED, possible abnormal states of each LED, and what to do if an LED indicates
an abnormal state.
To verify proper operation, complete the following steps.
1. Verify that the power supply's LED is steady green on the back of the device.
2. Verify that the power supply was placed in power supply bay #1 and operational by observing a
steady green LED lighting up "P1" on the front of the device.
LEDs for power and fans (located on front of device )TABLE 19
LED State Meaning
Fan (labeled Fn) On The fan tray is powered on and is operating normal.
Off The fan tray is not powered on, or has been removed.
PS1 (labeled P1) Off Power supply 1 is not installed or is not providing power.
Amber Power supply 1 is installed, but not connected or a fault is detected.
Green Steady Power supply 1 is installed and is functioning normally.
Green Blinking Power supply 1 has input power, but is not enabled and has no output
power.
PS2 (labeled P2) Off Power supply 2 is not installed or is not providing power.
Amber Power supply 2 is installed, but not connected or a fault is detected.
Green Steady Power supply 2 is installed and is functioning normally.
Green Blinking Power supply 2 has input power, but is not enabled and has no output
power.
The LEDs for Fan, PS1 and PS2 are located on the right side of the front panel for Brocade NetIron
CES Series and Brocade NetIron CER Series 2024 models (On the Brocade NetIron CES Series
2048 and Brocade NetIron CER Series 2048 models, these LEDs are located on the left side of the
front panel).
The software regularly polls the hardware for power status information. You can display the status
information from any management session. In addition, the software automatically generates a
Syslog message and SNMP trap if a status change occurs.
Displaying the status of the power supplies
You can display the status of the power supplies by entering the show chassis command at any level
of the CLI. The display shows whether a power supply is installed in the specified power supply slot
Verifying proper operation
92 Brocade NetIron CES 2000 Series and NetIron CER 2000 Series Hardware Installation Guide
53-1003263-02
- Brocade NetIron CES 2000 1
- Series and NetIron CER 1
- 2000 Series 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- About This Document 11
- Notice to the reader 12
- Related publications 13
- Product Overview 15
- Product overview 20
- Software features 21
- Upgrade applications 21
- Hardware features 22
- Control features 29
- Network interfaces 31
- Supported optics 31
- 10 Gigabit Ethernet ports 32
- Port regions 33
- Power supplies 34
- AC power supplies 35
- DC power supplies 35
- Cooling system and fans 36
- Password assignment 39
- IP address configuration 40
- Support of sub-net masks 41
- Device connection 43
- Installation 45
- Summary of installation tasks 46
- Installation precautions 47
- Installation site preparation 49
- Installing an AC power supply 50
- Installing a DC power supply 52
- Device installation 55
- Mid rack mount position 57
- Reverse rack mount position 58
- System power 59
- Operation verification 60
- Verifying proper operation 61
- PC or terminal attachment 63
- CLI Functionality 65
- Online help 66
- Command completion 66
- Scroll control 66
- Line editing commands 66
- Hardware Specifications 73
- Physical dimensions 74
- Operating environment 76
- Storage environment 76
- Safety agency approvals 77
- Electromagnetic approvals 77
- Port specifications 77
- Console port pin assignments 78
- Hardware Maintenance 81
- AC power supply 83
- Required tools 84
- Removing the DC power supply 86
- Replacing the fan tray 94
- Cabling a fiber optic module 96
- Tunable 10 GbE DWDM SFP+ 97
- Regulatory Statements 99
- China CC statement 100
- FCC warning (US only) 101
- VCCI statement 101
- Caution and Danger Notices 103
- Electrical cautions 105
- Danger Notices 110
- General dangers 111
- Electrical dangers 111
- Laser dangers 115
- 53-1003263-02 117
Related products and manuals for Network switches Brocade Communications Systems NetIron CER Series
(46 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals