Brocade Communications Systems ServerIron ADX 12.4.00 Service Manual Page 154
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ServerIron ADX Firewall Load Balancing Guide 143
53-1002436-01
Configuration example for FWLB-to-SLB
6
DRAFT: BROCADE CONFIDENTIAL
Binding the real server to the virtual server
To bind the real servers to the virtual server, enter the following commands on the internal
ServerIron ADX (ServerIron ADX
B). Notice that the port binding takes place on the Virtual Server
configuration level.
ServerIronADXB(config)# server virtual www.brocade.com
ServerIronADXB(config-vs-www.brocade.com)# bind http RS1 http
ServerIronADXB(config-vs-www.brocade.com)# bind http RS2 http
ServerIronADXB(config-vs-www.brocade.com)# exit
Syntax: [no] bind <port> <real server name> <port>
Enabling FWLB-to-SLB
To enable FWLB-to-SLB, enter the following command on the internal ServerIron ADX (ServerIron
ADX B).
ServerIronADXB(config)# server fw-slb
Syntax: [no] server fw-slb
Configuration example for FWLB-to-SLB
The following sections show all the ServerIron commands you would enter on each ServerIron ADX
to implement the FWLB-to-SLB configuration shown in
Figure 21 on page 137.
Commands on ServerIron A (external)
The following commands change the ServerIron’s host name to “ServerIronA", configure the
ServerIron ADX’s management IP address, and specify the default gateway.
ServerIronADX(config)# hostname ServerIronA
ServerIronADXA(config)# ip address 192.168.1.100 255.255.255.0
ServerIronADXA(config)# ip default-gateway 192.168.1.1
Enter the following commands to add two firewalls, FW1-IPin and FW2-IPin.
ServerIronADXA(config)# server fw-name FW1-IPin 192.168.1.30
ServerIronADXA(config-rs-FW1-IPin)# exit
ServerIronADXA(config)# server fw-name FW2-IPin 192.168.1.40
ServerIronADXA(config-rs-FW2-IPin)# exit
The following commands configure parameters for firewall group 2. The fwall-info commands
configure the paths for the firewall traffic. Each path consists of a path ID, the ServerIron ADX port
attached to the firewall, the IP address of the ServerIron ADX at the other end of the path, and the
next-hop IP address (usually the firewall interface connected to this ServerIron ADX). Make sure
you configure reciprocal paths on the other ServerIron ADX, as shown in the section containing the
CLI commands for ServerIron ADX B.
NOTE
Path information is required even if the firewalls are synchronized.
The fw-name <firewall-name> command adds the firewalls to the firewall group.
- ServerIron ADX 1
- Document History 2
- Contents 3
- About This Document 8
- Document conventions 9
- Notice to the reader 10
- Related publications 11
- ServerIron FWLB Overview 12
- Firewall environments 14
- Load balancing paths 15
- Firewall selection 17
- Hashing mechanism 17
- Stateful FWLB 18
- Health checks 18
- Path health checks 19
- Application health checks 19
- Firewall health check debug 21
- Basic FWLB topology 22
- HA FWLB topology 23
- Failover 24
- Router paths 24
- Multizone FWLB topology 25
- FWLB configuration limits 26
- Configuring Basic FWLB 28
- IPv4 Firewall-1 37
- IPv4 Firewall-2 37
- External 40
- Internal 40
- Firewall-2 42
- Firewall-1 42
- Configuring HA FWLB 48
- Session limits 49
- Session aging 49
- Task Reference 52
- Configuring the firewall port 53
- Configuring the partner port 54
- Configuring the router port 55
- Configuring the firewalls 55
- Adding the firewalls 55
- Connection rate control 57
- Complete CLI example 62
- HA FWLB with VRRP 73
- Usage notes 78
- Configuring Multizone FWLB 82
- Zone 3Zone 2 84
- Zone1-SI(config)# no span 85
- Failover algorithm 92
- Commands on Zone1-SI-A zone 1 92
- DRAFT: BROCADE CONFIDENTIAL 100
- 53-1002436-01 102
- SI-A SI-A 104
- In this chapter 124
- NAT firewalls 124
- Extra firewall method 129
- Access policy method 130
- Specifying the partner port 134
- Specifying the router ports 134
- Configuring FWLB and SLB 146
- Configuring SLB-to-FWLB 148
- Configuring the real servers 149
- Enabling SLB-to-FWLB 150
- Configuring FWLB-to-SLB 152
- Enabling FWLB-to-SLB 154
- FWLB configuration overview 166
- TCP/UDP port statistics 169
- FWLB path information 172
- Field Description 173
- • 6 – TCP 174
- • 17 – UDP 174
- In this appendix 176
- FWLB selection algorithms 182
- Configuration guidelines 186
- Denying FWLB 187
Related products and manuals for Network switches Brocade Communications Systems ServerIron ADX 12.4.00
(12 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.748 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals