Brocade Communications Systems VDX 8770-8 Installation Guide Page 23
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CAUTION
For the NEBS-compliant installation of a Brocade device with AC or DC systems, use a ground
wire of at least 2 AWG. The ground wire should have an agency-approved crimped connector
(provided with the device) attached to one end, with the other end attached to building ground.
The connector must be crimped with the proper tool, allowing it to be connected to both ground
screws on the enclosure. Before crimping the ground wire into the provided ground lug, ensure
that the bare copper wire has been cleaned and antioxidant is applied to the bare wire. In
addition, anti-rotation devices or lock washers must be used with all screw connections for the
grounding wire.
Preparing for the installation
Review the following before installing the device:
• Refer to Cautions and Danger Notices on page 107 to review safety precautions and translations.
• Refer to "NEBS requirements on page 21" to ensure compliance with NEBS-GR-1089 standards
• Refer to the Brocade VDX 8770 Switch Technical Specifications on page 95 to ensure power
supply standards are met before installing the chassis and to review the to environmental
requirements.
• Refer to "Preparing for the installation" section to plan for cable management.
DANGER
The procedures in this manual are for qualified service personnel.
NOTE
Brocade strongly recommends that devices be installed in environments that have minimal dust and
airborne contaminants.
The following steps are required to ensure correct installation and operation.
1. Ensure that doorways are wider than 91 cm (36 in.) to accommodate the device.
2. Provide a space that is 15 rack units (15U) high, 61.29 cm (24.09 in.) deep, and 43.74 cm (17.22 in.)
wide. One rack unit is equal to 4.45 cm (1.75 in.).
Plan to install the Brocade device with the port side facing the air-intake aisle. Airflow is from the port
side of the device to the fan side.
Ensure that the rack is balanced and mechanically secured to provide stability in the event of an
earthquake and that the equipment does not exceed the rack’s weight limits.
DANGER
Make sure the rack housing the device is adequately secured to prevent it from becoming
unstable or falling over.
3. Ensure that dedicated electrical branch circuits with the following characteristics are available:
• Up to eight dedicated fused 200-240 VAC, 50-60 Hz feeds or -48 VDC (one per power supply)
• One cable for each power supply
Preparing for the installation
Brocade VDX 8770-8 Hardware Installation Guide 23
53-1002564-07
- Brocade VDX 8770-8 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- Product Overview 11
- Hardware components 12
- Port side view 13
- Nonport side view 14
- Supported Line cards 15
- Breakout mode 16
- Trunking 16
- 27x40 GbE operating modes 17
- High availability 18
- Device Installation 19
- NEBS requirements 21
- Environmental requirements 25
- Chassis slots 25
- Port numbering 26
- FIGURE 4 12x40 GbE line card 27
- 48x10G-T port numbering 28
- 27x40 GbE port numbering 29
- 6x100 GbE port numbering 30
- Providing power to the device 31
- Connecting an AC power cord 32
- Connecting a DC power cord 32
- Initial Configuration 35
- Configuration tasks 36
- Changing the RBridge ID 39
- Assigning permanent passwords 39
- Configuring the IP addresses 40
- Customizing a host name 42
- Customizing a chassis name 42
- Setting the date and time 43
- Setting the time zone 44
- Verifying correct operation 46
- Backing up the configuration 47
- Connecting network devices 47
- Testing connectivity 48
- Managing cables 49
- System Monitoring 51
- 8x10 GbE line card 52
- 12x40 GbE line card 53
- 27x40 GbE line card 53
- 48x10G-T line card 55
- 6x100 GbE line card 56
- 1 Power LED 62
- 2 Status LED 62
- 1 AC power input LED (AC OK) 63
- 2 DC power output LED (DC OK) 63
- 3 Alarm LED (ALM) 63
- Introduction 69
- ESD precautions 69
- Time and items required 70
- Removing a line card 72
- Replacing a line card 73
- Removing a management module 75
- Replacing a management module 76
- Removing an AC power supply 80
- Replacing an AC power supply 81
- Removing a DC power supply 82
- Replacing a DC power supply 82
- Fan removal and replacement 83
- Replacing a fan 84
- Removing an air filter 86
- Replacing an air filter 86
- Removing a filler panel 86
- Replacing a filler panel 87
- Removing a transceiver 89
- Replacing a transceiver 90
- Removing a QSFP transceiver 90
- Cable routing table 91
- System specifications 95
- Ethernet 96
- Power consumption (modules) 100
- Memory specifications 102
- Regulatory compliance (EMC) 102
- 53-1002564-07 103
- Regulatory Statements 105
- VCCI statement 106
- China ROHS 106
- FCC warning (US only) 106
- Cautions and Danger Notices 107
- Danger Notices 112
- Electrical dangers 113
- Laser dangers 116
Related products and manuals for Network switches Brocade Communications Systems VDX 8770-8
(188 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.643 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals