Brocade Communications Systems VDX 8770-8 Installation Guide Page 61
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Management module LED descriptions (Continued)TABLE 9
LED purpose Color Status Recommended action
Status No light (LED is off) MM is either healthy or
does not have power.
Verify that the power LED
is on.
Steady amber MM requires attention or is
still booting up.
If the LED remains amber,
the module is faulty.
Consult your supplier.
Active Steady blue Module is the active MM. No action required.
No light (LED is off) Module is booting up,
negotiating to be the active
MM, or is the standby MM.
No action required.
Ethernet management link
(upper left)
Steady green Ethernet link speed is
1000 Mbps (1 Gbps).
No action required.
No light (LED is off) There is no link or link
speed is 10 or 100 Mbps.
No action required.
Ethernet management link
activity (upper right)
Blinking green Ethernet link is healthy and
traffic is flowing through
port.
No action required.
No light (LED is off) No traffic is flowing. No action required.
Determining the status of a switch fabric module
At least one functional switch fabric module (SFM) must be plugged into slots S3 or S4 (the "control
plane slots"). If there are no functional switch fabric module s in either slot during bootup, bootup is
halted with a message indicating that condition.
In an operational chassis, if all switch fabric module s in the control plane slots become faulty or are
removed, then all the line cards will be faulted with a reason code that indicates no availability of a
switch fabric module . An external RASlog message will also be displayed.
Complete the following steps to determine the status of a switch fabric module .
1. Locate the LED indicators on the switch fabric module (refer to Locating the LED indicators on the
switch fabric module on page 61). The LED patterns may temporarily change during POST and
other diagnostic tests. For information about how to interpret the LED patterns, refer to Interpreting
the switch fabric module LED indicators on page 62.
2. Use the show sfm command or the show slots command to see whether the switch fabric module is
enabled.
Locating the LED indicators on the switch fabric module
Use the following illustration to identify the LEDs on the switch fabric module.
Determining the status of a switch fabric module
Brocade VDX 8770-8 Hardware Installation Guide 61
53-1002564-07
- Brocade VDX 8770-8 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- Product Overview 11
- Hardware components 12
- Port side view 13
- Nonport side view 14
- Supported Line cards 15
- Breakout mode 16
- Trunking 16
- 27x40 GbE operating modes 17
- High availability 18
- Device Installation 19
- NEBS requirements 21
- Environmental requirements 25
- Chassis slots 25
- Port numbering 26
- FIGURE 4 12x40 GbE line card 27
- 48x10G-T port numbering 28
- 27x40 GbE port numbering 29
- 6x100 GbE port numbering 30
- Providing power to the device 31
- Connecting an AC power cord 32
- Connecting a DC power cord 32
- Initial Configuration 35
- Configuration tasks 36
- Changing the RBridge ID 39
- Assigning permanent passwords 39
- Configuring the IP addresses 40
- Customizing a host name 42
- Customizing a chassis name 42
- Setting the date and time 43
- Setting the time zone 44
- Verifying correct operation 46
- Backing up the configuration 47
- Connecting network devices 47
- Testing connectivity 48
- Managing cables 49
- System Monitoring 51
- 8x10 GbE line card 52
- 12x40 GbE line card 53
- 27x40 GbE line card 53
- 48x10G-T line card 55
- 6x100 GbE line card 56
- 1 Power LED 62
- 2 Status LED 62
- 1 AC power input LED (AC OK) 63
- 2 DC power output LED (DC OK) 63
- 3 Alarm LED (ALM) 63
- Introduction 69
- ESD precautions 69
- Time and items required 70
- Removing a line card 72
- Replacing a line card 73
- Removing a management module 75
- Replacing a management module 76
- Removing an AC power supply 80
- Replacing an AC power supply 81
- Removing a DC power supply 82
- Replacing a DC power supply 82
- Fan removal and replacement 83
- Replacing a fan 84
- Removing an air filter 86
- Replacing an air filter 86
- Removing a filler panel 86
- Replacing a filler panel 87
- Removing a transceiver 89
- Replacing a transceiver 90
- Removing a QSFP transceiver 90
- Cable routing table 91
- System specifications 95
- Ethernet 96
- Power consumption (modules) 100
- Memory specifications 102
- Regulatory compliance (EMC) 102
- 53-1002564-07 103
- Regulatory Statements 105
- VCCI statement 106
- China ROHS 106
- FCC warning (US only) 106
- Cautions and Danger Notices 107
- Danger Notices 112
- Electrical dangers 113
- Laser dangers 116
Related products and manuals for Network switches Brocade Communications Systems VDX 8770-8
(188 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.367 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals