Brocade Communications Systems VDX 8770-8 Installation Guide Page 51
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
System Monitoring
● Monitoring overview........................................................................................................ 51
● Determining the status of a line card...............................................................................51
● Determining the status of a management module.......................................................... 60
● Determining the status of a switch fabric module............................................................61
● Determining the status of a power supply....................................................................... 63
● Determining the status of a fan....................................................................................... 65
● Determining the status of a CID card.............................................................................. 66
Monitoring overview
The Brocade device is engineered for reliability and requires no routine operational steps or
maintenance. This section provides information about determining the status of each component using
LEDs and CLI commands. Refer to the Network OS Administration Guide for additional information.
There are two commands that can be especially helpful in monitoring the health status of various device
components. These commands are show chassis and the various show environment commands. For
details about these commands, refer to the Network OS Command Reference.
Determining the status of a line card
Use the following procedure to determine the status of a line card.
1. Locate the LEDs on the line card. Refer to the line card illustrations in the following sections.
The LED patterns may temporarily change during POST and other diagnostic tests. For information
about how to interpret the LED patterns, refer to Interpreting the line card LED indicators on page
56.
2. Use the show linecard or show slots command to determine if the line cards are enabled. The line
cards are labeled L1 through L8 in the output. The show linecard command limits the output to the
line card slots only.
3. Use the show interface command to determine the status of the interfaces (ports) on the line card,
Locating the LEDs on the line card
Use the following illustrations to locate the LEDs on the line cards available on the device.Full views
and close-ups are provided for each line card.
Brocade VDX 8770-8 Hardware Installation Guide
51
53-1002564-07
- Brocade VDX 8770-8 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- Product Overview 11
- Hardware components 12
- Port side view 13
- Nonport side view 14
- Supported Line cards 15
- Breakout mode 16
- Trunking 16
- 27x40 GbE operating modes 17
- High availability 18
- Device Installation 19
- NEBS requirements 21
- Environmental requirements 25
- Chassis slots 25
- Port numbering 26
- FIGURE 4 12x40 GbE line card 27
- 48x10G-T port numbering 28
- 27x40 GbE port numbering 29
- 6x100 GbE port numbering 30
- Providing power to the device 31
- Connecting an AC power cord 32
- Connecting a DC power cord 32
- Initial Configuration 35
- Configuration tasks 36
- Changing the RBridge ID 39
- Assigning permanent passwords 39
- Configuring the IP addresses 40
- Customizing a host name 42
- Customizing a chassis name 42
- Setting the date and time 43
- Setting the time zone 44
- Verifying correct operation 46
- Backing up the configuration 47
- Connecting network devices 47
- Testing connectivity 48
- Managing cables 49
- System Monitoring 51
- 8x10 GbE line card 52
- 12x40 GbE line card 53
- 27x40 GbE line card 53
- 48x10G-T line card 55
- 6x100 GbE line card 56
- 1 Power LED 62
- 2 Status LED 62
- 1 AC power input LED (AC OK) 63
- 2 DC power output LED (DC OK) 63
- 3 Alarm LED (ALM) 63
- Introduction 69
- ESD precautions 69
- Time and items required 70
- Removing a line card 72
- Replacing a line card 73
- Removing a management module 75
- Replacing a management module 76
- Removing an AC power supply 80
- Replacing an AC power supply 81
- Removing a DC power supply 82
- Replacing a DC power supply 82
- Fan removal and replacement 83
- Replacing a fan 84
- Removing an air filter 86
- Replacing an air filter 86
- Removing a filler panel 86
- Replacing a filler panel 87
- Removing a transceiver 89
- Replacing a transceiver 90
- Removing a QSFP transceiver 90
- Cable routing table 91
- System specifications 95
- Ethernet 96
- Power consumption (modules) 100
- Memory specifications 102
- Regulatory compliance (EMC) 102
- 53-1002564-07 103
- Regulatory Statements 105
- VCCI statement 106
- China ROHS 106
- FCC warning (US only) 106
- Cautions and Danger Notices 107
- Danger Notices 112
- Electrical dangers 113
- Laser dangers 116
Related products and manuals for Network switches Brocade Communications Systems VDX 8770-8
(188 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.219 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals