Brocade Communications Systems VDX 8770-8 Installation Guide Page 32
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Connecting an AC power cord
1. Plug the power cord into the power supply.
2. Route the cable so it will be out of the way when connected to the power source.
3. Plug the other end of the cable into the power source.
Connecting a DC power cord
1. Use a #1 Phillips screwdriver to remove the screw that secures the safety cover over the power lugs
and remove the safety cover.
2. Use a #2 Phillips screwdriver to unscrew the power lugs.
3. Obtain heat shrink tubing with the following specifications to install on the #2 AWG power supply
input wire:
• Inside diameter: 1.27 cm (.5 in.)
• Minimum 2:1/50% shrink ratio
• Nominal Rec. Wall Thickness: 30480 mm (.012 in.) minimum
• Dielectric strength: 800V/mil
• Tensile strength: greater than or equal to 5000 psi
• Operating temperature: -40°C to +150°C (-40°F to 302°F) minimum
• RoHS compliant
4. Cut off a 5.08 cm (2 in) lengths for each #2 AWG power supply wire.
5. Slide the tubing over the #2 AWG power supply wire.
6. Crimp the #2 AWG power supply wire into the power lug.
7. Slide the tubing over the lug to the brown strip closest to the lug holes.
8. Apply heat to shrink the tubing over the lug and wire insulation.
Installed tubing and lugs on power supply wire should conform to the following illustration.
1 Heatshrink tubing
2 Power lug
FIGURE 9 Heat shrink tubing and lug on DC power supply cable
9. Connect the power lugs to the power supply unit.
Connect the -48V wire to the negative terminal and the 0V wire to the positive terminal.
NOTE
The DC return must be isolated from the chassis ground (DC-I) when making connections to the
power supply.
Connecting an AC power cord
32 Brocade VDX 8770-8 Hardware Installation Guide
53-1002564-07
- Brocade VDX 8770-8 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- Product Overview 11
- Hardware components 12
- Port side view 13
- Nonport side view 14
- Supported Line cards 15
- Breakout mode 16
- Trunking 16
- 27x40 GbE operating modes 17
- High availability 18
- Device Installation 19
- NEBS requirements 21
- Environmental requirements 25
- Chassis slots 25
- Port numbering 26
- FIGURE 4 12x40 GbE line card 27
- 48x10G-T port numbering 28
- 27x40 GbE port numbering 29
- 6x100 GbE port numbering 30
- Providing power to the device 31
- Connecting an AC power cord 32
- Connecting a DC power cord 32
- Initial Configuration 35
- Configuration tasks 36
- Changing the RBridge ID 39
- Assigning permanent passwords 39
- Configuring the IP addresses 40
- Customizing a host name 42
- Customizing a chassis name 42
- Setting the date and time 43
- Setting the time zone 44
- Verifying correct operation 46
- Backing up the configuration 47
- Connecting network devices 47
- Testing connectivity 48
- Managing cables 49
- System Monitoring 51
- 8x10 GbE line card 52
- 12x40 GbE line card 53
- 27x40 GbE line card 53
- 48x10G-T line card 55
- 6x100 GbE line card 56
- 1 Power LED 62
- 2 Status LED 62
- 1 AC power input LED (AC OK) 63
- 2 DC power output LED (DC OK) 63
- 3 Alarm LED (ALM) 63
- Introduction 69
- ESD precautions 69
- Time and items required 70
- Removing a line card 72
- Replacing a line card 73
- Removing a management module 75
- Replacing a management module 76
- Removing an AC power supply 80
- Replacing an AC power supply 81
- Removing a DC power supply 82
- Replacing a DC power supply 82
- Fan removal and replacement 83
- Replacing a fan 84
- Removing an air filter 86
- Replacing an air filter 86
- Removing a filler panel 86
- Replacing a filler panel 87
- Removing a transceiver 89
- Replacing a transceiver 90
- Removing a QSFP transceiver 90
- Cable routing table 91
- System specifications 95
- Ethernet 96
- Power consumption (modules) 100
- Memory specifications 102
- Regulatory compliance (EMC) 102
- 53-1002564-07 103
- Regulatory Statements 105
- VCCI statement 106
- China ROHS 106
- FCC warning (US only) 106
- Cautions and Danger Notices 107
- Danger Notices 112
- Electrical dangers 113
- Laser dangers 116
Related products and manuals for Network switches Brocade Communications Systems VDX 8770-8
(188 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.983 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals