Brocade Communications Systems VDX 8770-8 Installation Guide Page 25
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Environmental requirements
Ensure that the environmental requirements are met. Refer to the Brocade VDX 8770 Switch Technical
Specifications on page 95.
CAUTION
Do not install the device in an environment where the operating ambient temperature might
exceed 40°C (104°F).
NOTE
The 0° to 40°C (32° to 104°F) range applies to the ambient air temperature at the air intake vents on the
port side of the device.The temperature inside the chassis can reach up to 90°C (194°F) for some
modules during operation. Brocade recommends that the internal temperature not exceed 75°C
(167°F). Cooling policy is based on a combination of ambient temperature and measured temperature
on the modules. Various combinations will result in an increase in fan speed to create more cooling in
the device. If a component approaches a critical temperature that will trigger a module shutdown, there
will be a WARNING message in the RASlog, followed by a CRITICAL message saying that the module
will shut down in two minutes.Use the show environment command to view temperature status.
Chassis slots
Chassis slots are coded and numbered to differentiate between management module slots, switch
fabric module slots, and line card slots. Management modules (MMs) must be installed only in slots M1
and M2. switch fabric modules (SFMs) must be installed only in slots S1 through S6. There must be at
least one switch fabric module installed in either slot S3 or slot S4. The line card slots, L1 through L8,
can be filled with any supported line cards. Unused slots must be filled with the correct filler panels to
maintain adequate cooling.
Unpacking and installing the device
DANGER
A fully populated Brocade device weighs between 86.18 kg (190 lb) and 165.56 kg (365 lb) and
requires a hydraulic or assisted lift to install it.
DANGER
Use safe lifting practices when moving the product.
1. Unpack the device.
a) Cut the bands that encircle the packaging.
b) Slide the upper portion of the cardboard shipping box up off the pallet and shipping tray.
NOTE
The product packaging incorporates a wood pallet and brackets. The device sits on top of a
corrugated cardboard shipping tray.
Environmental requirements
Brocade VDX 8770-8 Hardware Installation Guide 25
53-1002564-07
- Brocade VDX 8770-8 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- Product Overview 11
- Hardware components 12
- Port side view 13
- Nonport side view 14
- Supported Line cards 15
- Breakout mode 16
- Trunking 16
- 27x40 GbE operating modes 17
- High availability 18
- Device Installation 19
- NEBS requirements 21
- Environmental requirements 25
- Chassis slots 25
- Port numbering 26
- FIGURE 4 12x40 GbE line card 27
- 48x10G-T port numbering 28
- 27x40 GbE port numbering 29
- 6x100 GbE port numbering 30
- Providing power to the device 31
- Connecting an AC power cord 32
- Connecting a DC power cord 32
- Initial Configuration 35
- Configuration tasks 36
- Changing the RBridge ID 39
- Assigning permanent passwords 39
- Configuring the IP addresses 40
- Customizing a host name 42
- Customizing a chassis name 42
- Setting the date and time 43
- Setting the time zone 44
- Verifying correct operation 46
- Backing up the configuration 47
- Connecting network devices 47
- Testing connectivity 48
- Managing cables 49
- System Monitoring 51
- 8x10 GbE line card 52
- 12x40 GbE line card 53
- 27x40 GbE line card 53
- 48x10G-T line card 55
- 6x100 GbE line card 56
- 1 Power LED 62
- 2 Status LED 62
- 1 AC power input LED (AC OK) 63
- 2 DC power output LED (DC OK) 63
- 3 Alarm LED (ALM) 63
- Introduction 69
- ESD precautions 69
- Time and items required 70
- Removing a line card 72
- Replacing a line card 73
- Removing a management module 75
- Replacing a management module 76
- Removing an AC power supply 80
- Replacing an AC power supply 81
- Removing a DC power supply 82
- Replacing a DC power supply 82
- Fan removal and replacement 83
- Replacing a fan 84
- Removing an air filter 86
- Replacing an air filter 86
- Removing a filler panel 86
- Replacing a filler panel 87
- Removing a transceiver 89
- Replacing a transceiver 90
- Removing a QSFP transceiver 90
- Cable routing table 91
- System specifications 95
- Ethernet 96
- Power consumption (modules) 100
- Memory specifications 102
- Regulatory compliance (EMC) 102
- 53-1002564-07 103
- Regulatory Statements 105
- VCCI statement 106
- China ROHS 106
- FCC warning (US only) 106
- Cautions and Danger Notices 107
- Danger Notices 112
- Electrical dangers 113
- Laser dangers 116
Related products and manuals for Network switches Brocade Communications Systems VDX 8770-8
(188 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.007 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals