Brocade Communications Systems VDX 8770-8 Installation Guide Page 74
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
a) Make sure that you have cleared the configuration for the original line card from the
chassis database using steps under Removing a line card on page 72.
b) Enter the linecard slot_number command followed by a question mark (?) to display the
current line card types.
c) Enter the linecard slot_number linecard_type command using the proper line card type for
the new line card.
d) Enter the exit command twice to return to privileged EXEC mode.
2. Unpack the new line card and remove it from the anti-static bag.
3. Inspect the line card for damage.
4. Remove the protective covers from the backplane connectors.
5. Orient the line card so that the ports are at the front of the device.
6. Open the ejectors by rotating them toward the center of the line card face and align the flat side of
the line card inside the top and bottom rail guides in the slot. Line cards can be inserted in any of
the slots labeled L1 through L8.
7. Slide the line card all the way into the slot.
8. Close the ejectors by rotating them away from the center of the line card. The levering action of the
ejectors seats the line card in the slot.
9. Tighten the captive screws using the Phillips screwdriver.
10.Check to see if the line card has powered on. If not, power on the line card using the power-on
linecard slot_number command.
Verify that the power LED on the line card is displaying a steady green light. If it does not turn on,
ensure that the line card is firmly seated.
The status LED on the line card will show amber until POST completes for the line card. It should
then turn off. If it remains amber, the line card may not be properly seated in the backplane or the
line card may be faulty.
11.If you have replaced a line card with a line card of a different type, follow these steps:
a) Save the configuration persistently by issuing the copy running-config startup-config
command after the interface module reaches the online state.
b) Verify the configuration by issuing the show running-config linecard linecard command.
12.Reinstall the transceivers and cables in the line card or install new transceivers and cables if you
have installed a different type of line card.
13.Group and route the cables through the cable management device.
Management module removal and replacement
This section describes how to remove and replace a management module (MM). Each device can
have one or two management modules. They reside in slots M1 and M2. There must be at least one
management module installed for the chassis to operate.
Time and items required
The replacement procedure for the management module takes approximately 30 minutes. The
following items are required for the management module replacement:
• ESD grounding strap
• Workstation computer
• Serial cable
• IP address of an FTP server for backing up the configuration
Management module removal and replacement
74 Brocade VDX 8770-8 Hardware Installation Guide
53-1002564-07
- Brocade VDX 8770-8 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- Product Overview 11
- Hardware components 12
- Port side view 13
- Nonport side view 14
- Supported Line cards 15
- Breakout mode 16
- Trunking 16
- 27x40 GbE operating modes 17
- High availability 18
- Device Installation 19
- NEBS requirements 21
- Environmental requirements 25
- Chassis slots 25
- Port numbering 26
- FIGURE 4 12x40 GbE line card 27
- 48x10G-T port numbering 28
- 27x40 GbE port numbering 29
- 6x100 GbE port numbering 30
- Providing power to the device 31
- Connecting an AC power cord 32
- Connecting a DC power cord 32
- Initial Configuration 35
- Configuration tasks 36
- Changing the RBridge ID 39
- Assigning permanent passwords 39
- Configuring the IP addresses 40
- Customizing a host name 42
- Customizing a chassis name 42
- Setting the date and time 43
- Setting the time zone 44
- Verifying correct operation 46
- Backing up the configuration 47
- Connecting network devices 47
- Testing connectivity 48
- Managing cables 49
- System Monitoring 51
- 8x10 GbE line card 52
- 12x40 GbE line card 53
- 27x40 GbE line card 53
- 48x10G-T line card 55
- 6x100 GbE line card 56
- 1 Power LED 62
- 2 Status LED 62
- 1 AC power input LED (AC OK) 63
- 2 DC power output LED (DC OK) 63
- 3 Alarm LED (ALM) 63
- Introduction 69
- ESD precautions 69
- Time and items required 70
- Removing a line card 72
- Replacing a line card 73
- Removing a management module 75
- Replacing a management module 76
- Removing an AC power supply 80
- Replacing an AC power supply 81
- Removing a DC power supply 82
- Replacing a DC power supply 82
- Fan removal and replacement 83
- Replacing a fan 84
- Removing an air filter 86
- Replacing an air filter 86
- Removing a filler panel 86
- Replacing a filler panel 87
- Removing a transceiver 89
- Replacing a transceiver 90
- Removing a QSFP transceiver 90
- Cable routing table 91
- System specifications 95
- Ethernet 96
- Power consumption (modules) 100
- Memory specifications 102
- Regulatory compliance (EMC) 102
- 53-1002564-07 103
- Regulatory Statements 105
- VCCI statement 106
- China ROHS 106
- FCC warning (US only) 106
- Cautions and Danger Notices 107
- Danger Notices 112
- Electrical dangers 113
- Laser dangers 116
Related products and manuals for Network switches Brocade Communications Systems VDX 8770-8
(188 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.327 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals