Brocade Communications Systems Brocade Superx Series Installation Guide Page 151
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Brocade FastIron SX Series Chassis Hardware Installation Guide 139
53-1002500-01
Replacing the FSX 1600 fan assemblies
6
FIGURE 61 Removing the fan tray
4. Insert the new fan tray into the fan slot and push on the latch until the face plate is flush with
the chassis. Pushing the latch in seats the fan connector with the chassis connector.
5. Access the CLI, and enter the show chassis command to verify that the new fan is operating
normally.
Replacing the FSX 1600 fan assemblies
The FSX 1600 has two fan assemblies, both accessible from the rear. Each assembly has a fan
which pulls warm air out of the chassis.
You can remove and replace a fan assembly while the FSX 1600 chassis is powered on and
running.
To replace the fan tray, you need the following:
• A new fan assembly, which you can order from Brocade
• An ESD strap (provided with the fan assembly kit) or an ESD wrist strap with a plug for
connection to the ESD connector on the chassis.
• In addition to the above, you might also need a #2 Phillips-head screwdriver.
1Fan Tray Latch
2Fan Tray
Fan Tray
Fan Tray Latch
- Brocade FastIron SX Series 1
- Document History 2
- Contents 3
- About This Document 9
- Text formatting 10
- Command syntax conventions 10
- Notice to the reader 11
- Related publications 11
- Document feedback 12
- Product Overview 13
- PoE port density 14
- PoE+ port density 14
- Software features 15
- PoE and PoE+ applications 16
- Support for IPv6 modules 16
- Hardware features 16
- FSX 800 chassis 17
- FIGURE 2 FSX 800 module slots 18
- FSX 1600 chassis 19
- FIGURE 4 FSX 1600 slots 21
- Management modules 22
- Switch fabric modules 25
- Interface modules 25
- Hot swap support 26
- LED Position State Meaning 28
- 2Port 2 14Port 14 29
- • 24 10/100/1000 copper ports 30
- • 24 LEDs for port status 30
- • 24 LEDs for PoE status 30
- • 24 LEDs 32
- 1Port 1 13 Port 13 35
- 2Port 2 24 Port 24 35
- Network interfaces 37
- Port regions 38
- Power supplies 39
- • Non-PoE devices: 40
- • PoE devices: 40
- • PoE+ devices: 41
- 2nd POE Power Supply 42
- Replacement power supplies 43
- SYSEJECT 44
- Power supply LEDs 45
- Cooling system 46
- Built-in mounting brackets 47
- Unpacking the system 49
- Installation precautions 50
- Cabling infrastructure 53
- Installation location 53
- Removing the slot panels 57
- Powering on the system 64
- Rear View Detail 69
- • Verify that the connection 71
- • Make sure that the power 71
- • Make sure that the wall 71
- Displaying the module status 72
- Assigning permanent passwords 75
- Configuring IP addresses 77
- Brocade# erase startup-config 78
- Brocade# configure terminal 78
- Brocade(config)# 78
- Brocade(config)# int e 1/5 78
- IPv6 devices 79
- Brocade> enable 81
- Connecting network devices 82
- Using a CX4 transceiver 85
- Testing network connectivity 86
- LED Desired 87
- Field Definition 92
- Managing the cooling system 94
- 4High 50 C80 C 100 78 dB 97
- 3Medium49 C59C 50 66 dB 97
- 1Low N/A 57 C 25 56 dB 97
- Monitoring the cooling system 99
- Displaying the temperature 100
- This Field... Displays 101
- Static and dynamic buffers 102
- (FSX 800 and FSX 1600 only) 103
- 53-1002500-01 104
- Removing MAC address entries 105
- Overview 107
- Management module switchover 108
- Switchover implications 109
- Management sessions 110
- Syslog and SNMP traps 110
- MAC address changes 110
- Status LED 114
- Software 114
- Maintaining the Hardware 117
- Replacing a management module 118
- 1 Management module 121
- 1Switch Fabric module 123
- Replacing an interface module 124
- Removing an interface module 125
- Brocade# disable module 3 128
- 1Interface module 128
- Brocade# enable module 3 129
- Brocade# disable module 1 129
- 1 Connector slots 130
- FIGURE 54 POE daughter card 131
- 24-port Gig Copper + PoE 132
- 1Bail Latch 133
- Cabling a fiber optic module 134
- Removing an AC power supply 135
- 1 Latch retaining screw 136
- 2 Latch retaining screw 136
- Removing a DC power supply 137
- DC IN DC OUT ALM 139
- Installing a new power supply 140
- Tighten the retaining screw 142
- EJECT SYS 143
- EJECT POE 143
- 1Cord retainer 144
- 2DC power 147
- Verifying proper operation 148
- Chassis front Chassis rear 150
- Fan Tray 151
- Fan Tray Latch 151
- Fan Assembly 152
- Filter Retainer 153
- Grab-strap 153
- Hardware Specifications 155
- Description Range 156
- FSX 1600 157
- Regulatory compliance 158
- Maximum power consumption 159
- Power source interruptions 160
- Pinouts and signalling 160
- Serial (console) port pinouts 161
- Chassis specifications 162
- Cable specifications 163
- Power cords 164
- Power supply specifications 165
- Electrical specifications 166
- Input connector and plug 167
- Description Certifications 169
- Safety warnings 170
- Regulatory Statements 171
- BSMI statement (Taiwan) 173
- Caution and Danger Notices 175
- Cautions 176
Related products and manuals for Network switches Brocade Communications Systems Brocade Superx Series
(330 pages)© 2020, manymanuals.com. All rights reserved. | 0.755 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals