Brocade Communications Systems Brocade Superx Series Installation Guide Page 72
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
60 Brocade FastIron SX Series Chassis Hardware Installation Guide
53-1002500-01
Verifying proper operation
2
If a problem persists after taking action described in this table, contact Brocade’s technical
support.
Displaying the module status
After you have attached a PC or terminal to the management module’s Console port or Ethernet
port and the Brocade device has initialized successfully, press Enter to display the following CLI
prompt in the terminal emulation window.
FastIron>
If you do not see this prompt, complete the following steps.
1. Make sure the cable is securely connected to your PC or terminal and the Console port or
Ethernet port.
2. Check the settings in your terminal emulation program. In addition to the session settings
listed in “Attaching a PC or terminal to the console port or 10/100/1000 copper port” on
page 51, make sure the terminal emulation session is running on the same serial port you
attached to the Console port.
If you view the prompt FastIron> or similar, you are connected to the system and can display the
status of the modules using the CLI. Enter the show module command at any CLI level.
DC IN (DC
supply only)
Green (steady) The power supply is receiving DC
power from a DC power source
OFF The power supply is not
receiving power from a DC
power source. You can do the
following:
• Make sure that the power
supply cables are
connected securely to the
power source and the
power supply.
• Make sure that the DC
power source is 48VDC @
30 A.
• Make sure that the power
source has power.
DC OUT ON – Green
(steady)
The power supply is supplying DC
output power to the chassis
OFF The power supply is not
supplying DC output power to
the chassis.
If this occurs and the AC OK (AC
power supply) or DC IN (DC
power supply) LED is Green,
then there is a problem with the
power supply and it must be
replaced.
ALM OFF No alarms present and the power
supply is in normal operating
condition.
Amber There is an alarm present and
the power supply is
malfunctioning.
Verify the AC or DC input and DC
output voltages.
TABLE 20 Desired and abnormal LED states after system power-on. (Continued)
LED Desired State Meaning Abnormal
State
Meaning or Action
- Brocade FastIron SX Series 1
- Document History 2
- Contents 3
- About This Document 9
- Text formatting 10
- Command syntax conventions 10
- Notice to the reader 11
- Related publications 11
- Document feedback 12
- Product Overview 13
- PoE port density 14
- PoE+ port density 14
- Software features 15
- PoE and PoE+ applications 16
- Support for IPv6 modules 16
- Hardware features 16
- FSX 800 chassis 17
- FIGURE 2 FSX 800 module slots 18
- FSX 1600 chassis 19
- FIGURE 4 FSX 1600 slots 21
- Management modules 22
- Switch fabric modules 25
- Interface modules 25
- Hot swap support 26
- LED Position State Meaning 28
- 2Port 2 14Port 14 29
- • 24 10/100/1000 copper ports 30
- • 24 LEDs for port status 30
- • 24 LEDs for PoE status 30
- • 24 LEDs 32
- 1Port 1 13 Port 13 35
- 2Port 2 24 Port 24 35
- Network interfaces 37
- Port regions 38
- Power supplies 39
- • Non-PoE devices: 40
- • PoE devices: 40
- • PoE+ devices: 41
- 2nd POE Power Supply 42
- Replacement power supplies 43
- SYSEJECT 44
- Power supply LEDs 45
- Cooling system 46
- Built-in mounting brackets 47
- Unpacking the system 49
- Installation precautions 50
- Cabling infrastructure 53
- Installation location 53
- Removing the slot panels 57
- Powering on the system 64
- Rear View Detail 69
- • Verify that the connection 71
- • Make sure that the power 71
- • Make sure that the wall 71
- Displaying the module status 72
- Assigning permanent passwords 75
- Configuring IP addresses 77
- Brocade# erase startup-config 78
- Brocade# configure terminal 78
- Brocade(config)# 78
- Brocade(config)# int e 1/5 78
- IPv6 devices 79
- Brocade> enable 81
- Connecting network devices 82
- Using a CX4 transceiver 85
- Testing network connectivity 86
- LED Desired 87
- Field Definition 92
- Managing the cooling system 94
- 4High 50 C80 C 100 78 dB 97
- 3Medium49 C59C 50 66 dB 97
- 1Low N/A 57 C 25 56 dB 97
- Monitoring the cooling system 99
- Displaying the temperature 100
- This Field... Displays 101
- Static and dynamic buffers 102
- (FSX 800 and FSX 1600 only) 103
- 53-1002500-01 104
- Removing MAC address entries 105
- Overview 107
- Management module switchover 108
- Switchover implications 109
- Management sessions 110
- Syslog and SNMP traps 110
- MAC address changes 110
- Status LED 114
- Software 114
- Maintaining the Hardware 117
- Replacing a management module 118
- 1 Management module 121
- 1Switch Fabric module 123
- Replacing an interface module 124
- Removing an interface module 125
- Brocade# disable module 3 128
- 1Interface module 128
- Brocade# enable module 3 129
- Brocade# disable module 1 129
- 1 Connector slots 130
- FIGURE 54 POE daughter card 131
- 24-port Gig Copper + PoE 132
- 1Bail Latch 133
- Cabling a fiber optic module 134
- Removing an AC power supply 135
- 1 Latch retaining screw 136
- 2 Latch retaining screw 136
- Removing a DC power supply 137
- DC IN DC OUT ALM 139
- Installing a new power supply 140
- Tighten the retaining screw 142
- EJECT SYS 143
- EJECT POE 143
- 1Cord retainer 144
- 2DC power 147
- Verifying proper operation 148
- Chassis front Chassis rear 150
- Fan Tray 151
- Fan Tray Latch 151
- Fan Assembly 152
- Filter Retainer 153
- Grab-strap 153
- Hardware Specifications 155
- Description Range 156
- FSX 1600 157
- Regulatory compliance 158
- Maximum power consumption 159
- Power source interruptions 160
- Pinouts and signalling 160
- Serial (console) port pinouts 161
- Chassis specifications 162
- Cable specifications 163
- Power cords 164
- Power supply specifications 165
- Electrical specifications 166
- Input connector and plug 167
- Description Certifications 169
- Safety warnings 170
- Regulatory Statements 171
- BSMI statement (Taiwan) 173
- Caution and Danger Notices 175
- Cautions 176
Related products and manuals for Network switches Brocade Communications Systems Brocade Superx Series
(330 pages)© 2020, manymanuals.com. All rights reserved. | 0.493 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals