Brocade Communications Systems Brocade Superx Series Installation Guide Page 26
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
14 Brocade FastIron SX Series Chassis Hardware Installation Guide
53-1002500-01
Hardware features
1
Hot swap support
• Interface modules are hot swappable, which means you can remove and replace them without
powering down the system; however, you must issue the disable module command before you
remove the modules from the device.
• Issuing the disable module command before removing the module is not required on the FSX
800 and FSX 1600 device. This is referred to as “Enhanced Hot Swap”.
• Do not perform both hotswap removal and hot swap insertion of another line module while hot
swap of a line module is taking place. Wait until the current hot swap of the line module is
completed. The following message indicates that the hot swap insertion of a module is
completed:
Module 1 is up and running
The following console message indicates that the hot swap removal of a module is completed:
Powering off the module in slot 1
24-port Gigabit Ethernet copper with
PoE
SX-FI424P X X
24-port 100/1000 Hybrid Fiber SX-FI424HF X X
2-port 10-Gigabit Ethernet LAN
module
SX-FI42XG X X
2-port 10-Gigabit Ethernet LAN or
WAN module
SX-FI42XGW X X
IPv6 Interface Modules
24-port Gigabit Ethernet copper
without PoE
SX-FI624C X X
24-port Gigabit Ethernet copper with
PoE
SX-FI624P X X
24-port 100/1000 Hybrid Fiber SX-FI624HF X X
2-port 10-Gigabit Ethernet LAN
module
SX-FI62XG X X
IPv4 and IPv6 Interface Modules
24-port Gigabit Ethernet copper
interface module with PoE+
SX-FI-24GPP X X
24-port Gigabit Ethernet fiber
interface module
SX-FI-24HF X X
2-port 10-Gigabit Ethernet interface
module
SX-FI-2XG X X
8-port 10-Gigabit Ethernet interface
module
SX-FI-8XG X X
48-port 10/100/1000 Mbps RJ45
Ethernet module with PoE+
SX-FI48GPP X X
TABLE 7 Interface modules (Continued)
Interface Module Part Number FSX 800 FSX 1600
- Brocade FastIron SX Series 1
- Document History 2
- Contents 3
- About This Document 9
- Text formatting 10
- Command syntax conventions 10
- Notice to the reader 11
- Related publications 11
- Document feedback 12
- Product Overview 13
- PoE port density 14
- PoE+ port density 14
- Software features 15
- PoE and PoE+ applications 16
- Support for IPv6 modules 16
- Hardware features 16
- FSX 800 chassis 17
- FIGURE 2 FSX 800 module slots 18
- FSX 1600 chassis 19
- FIGURE 4 FSX 1600 slots 21
- Management modules 22
- Switch fabric modules 25
- Interface modules 25
- Hot swap support 26
- LED Position State Meaning 28
- 2Port 2 14Port 14 29
- • 24 10/100/1000 copper ports 30
- • 24 LEDs for port status 30
- • 24 LEDs for PoE status 30
- • 24 LEDs 32
- 1Port 1 13 Port 13 35
- 2Port 2 24 Port 24 35
- Network interfaces 37
- Port regions 38
- Power supplies 39
- • Non-PoE devices: 40
- • PoE devices: 40
- • PoE+ devices: 41
- 2nd POE Power Supply 42
- Replacement power supplies 43
- SYSEJECT 44
- Power supply LEDs 45
- Cooling system 46
- Built-in mounting brackets 47
- Unpacking the system 49
- Installation precautions 50
- Cabling infrastructure 53
- Installation location 53
- Removing the slot panels 57
- Powering on the system 64
- Rear View Detail 69
- • Verify that the connection 71
- • Make sure that the power 71
- • Make sure that the wall 71
- Displaying the module status 72
- Assigning permanent passwords 75
- Configuring IP addresses 77
- Brocade# erase startup-config 78
- Brocade# configure terminal 78
- Brocade(config)# 78
- Brocade(config)# int e 1/5 78
- IPv6 devices 79
- Brocade> enable 81
- Connecting network devices 82
- Using a CX4 transceiver 85
- Testing network connectivity 86
- LED Desired 87
- Field Definition 92
- Managing the cooling system 94
- 4High 50 C80 C 100 78 dB 97
- 3Medium49 C59C 50 66 dB 97
- 1Low N/A 57 C 25 56 dB 97
- Monitoring the cooling system 99
- Displaying the temperature 100
- This Field... Displays 101
- Static and dynamic buffers 102
- (FSX 800 and FSX 1600 only) 103
- 53-1002500-01 104
- Removing MAC address entries 105
- Overview 107
- Management module switchover 108
- Switchover implications 109
- Management sessions 110
- Syslog and SNMP traps 110
- MAC address changes 110
- Status LED 114
- Software 114
- Maintaining the Hardware 117
- Replacing a management module 118
- 1 Management module 121
- 1Switch Fabric module 123
- Replacing an interface module 124
- Removing an interface module 125
- Brocade# disable module 3 128
- 1Interface module 128
- Brocade# enable module 3 129
- Brocade# disable module 1 129
- 1 Connector slots 130
- FIGURE 54 POE daughter card 131
- 24-port Gig Copper + PoE 132
- 1Bail Latch 133
- Cabling a fiber optic module 134
- Removing an AC power supply 135
- 1 Latch retaining screw 136
- 2 Latch retaining screw 136
- Removing a DC power supply 137
- DC IN DC OUT ALM 139
- Installing a new power supply 140
- Tighten the retaining screw 142
- EJECT SYS 143
- EJECT POE 143
- 1Cord retainer 144
- 2DC power 147
- Verifying proper operation 148
- Chassis front Chassis rear 150
- Fan Tray 151
- Fan Tray Latch 151
- Fan Assembly 152
- Filter Retainer 153
- Grab-strap 153
- Hardware Specifications 155
- Description Range 156
- FSX 1600 157
- Regulatory compliance 158
- Maximum power consumption 159
- Power source interruptions 160
- Pinouts and signalling 160
- Serial (console) port pinouts 161
- Chassis specifications 162
- Cable specifications 163
- Power cords 164
- Power supply specifications 165
- Electrical specifications 166
- Input connector and plug 167
- Description Certifications 169
- Safety warnings 170
- Regulatory Statements 171
- BSMI statement (Taiwan) 173
- Caution and Danger Notices 175
- Cautions 176
Related products and manuals for Network switches Brocade Communications Systems Brocade Superx Series
(330 pages)© 2020, manymanuals.com. All rights reserved. | 1.530 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals