Brocade Communications Systems ServerIron ADX 12.4.00 Service Manual Page 118
- Page / 188
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ServerIron ADX Firewall Load Balancing Guide 107
53-1002436-01
Configuration examples with Layer 3 routing
4
DRAFT: BROCADE CONFIDENTIAL
Zone1-SI-S(config-rs-fw2)# port http
Zone1-SI-S(config-rs-fw2)# port http no-health-check
Zone1-SI-S(config-rs-fw2)# port snmp
Zone1-SI-S(config-rs-fw2)# port snmp no-health-check
Zone1-SI-S(config-rs-fw2)# exit
Zone1-SI-S(config)# server fw-group 2
Zone1-SI-S(config-fw-2)# fw-name fw1
Zone1-SI-S(config-fw-2)# fw-name fw2
Zone1-SI-S(config-fw-2)# sym-priority 1
Zone1-SI-S(config-fw-2)# fwall-info 1 4/11 10.10.2.222 10.10.1.1
Zone1-SI-S(config-fw-2)# fwall-info 2 4/1 10.10.2.222 10.10.1.2
Zone1-SI-S(config-fw-2)# fwall-info 3 4/11 10.10.2.223 10.10.1.1
Zone1-SI-S(config-fw-2)# fwall-info 4 4/1 10.10.2.223 10.10.1.2
Zone1-SI-S(config-fw-2)# fwall-info 5 4/11 10.10.3.111 10.10.1.1
Zone1-SI-S(config-fw-2)# fwall-info 6 4/1 10.10.3.111 10.10.1.2
Zone1-SI-S(config-fw-2)# exit
Zone1-SI-S(config-fw-2)# fw-predictor per-service-least-conn
Zone1-SI-S(config-fw-2)# exit
Zone1-SI-S(config)# access-list 2 permit 10.10.2.0 0.0.0.255
Zone1-SI-S(config)# access-list 2 permit 10.10.8.0 0.0.0.255
Zone1-SI-S(config)# server fw-group 2
Zone1-SI-S(config-fw-2)# fwall-zone Zone2 2 2
Zone1-SI-S(config-fw-2)# exit
Zone1-SI-S(config)# server remote-name web1 10.10.8.40
Zone1-SI-S(config-rs-web1)# port http
Zone1-SI-S(config-rs-web1)# exit
Zone1-SI-S(config)# server remote-name web2 10.10.8.42
Zone1-SI-S(config-rs-web2)# port http
Zone1-SI-S(config-rs-web2)# exit
Zone1-SI-S(config)# server remote-name web3 10.10.6.41
Zone1-SI-S(config-rs-web3)# port http
Zone1-SI-S(config-rs-web3)# exit
Zone1-SI-S(config)# server remote-name web4 10.10.6.43
Zone1-SI-S(config-rs-web4)# port http
Zone1-SI-S(config-rs-web4)# exit
Zone1-SI-S(config)# server virtual www.web.com 10.10.1.10
Zone1-SI-S(config-vs-www.web.com)# port http
Zone1-SI-S(config-vs-www.web.com)# bind http web1 http web2 http web3 http web4
http
Zone1-SI-S(config-vs-www.web.com)# exit
Zone1-SI-S(config)# server slb-fw
Zone1-SI-S(config)# write memory
Commands on zone 2’s active ServerIron ADX (Zone2-SI-A)
The following commands configure ServerIron ADX Zone2-SI-A in zone 2. The configuration is
similar to the configuration for ServerIron ADX Zone1-SI-A, except the ACL and zone information are
for zone 3, and FWLB-to-SLB is enabled instead of SLB-to-FWLB.
ServerIronADX> enable
ServerIronADX# configure terminal
ServerIronADX(config)# hostname Zone2-SI-A
Zone2-SI-A(config)# vlan 1
Zone2-SI-A(config-vlan-1)# always-active
Zone1-SI-A(config)# vlan 2
Zone1-SI-A(config-vlan-2)# always-active
Zone1-SI-A(config-vlan-2)# tagged ethernet 4/11 to 4/12
Zone1-SI-A(config-vlan-2)# untagged ethernet 4/1 to 4/8
Zone1-SI-A(config-vlan-2)# router-interface ve 1
- ServerIron ADX 1
- Document History 2
- Contents 3
- About This Document 8
- Document conventions 9
- Notice to the reader 10
- Related publications 11
- ServerIron FWLB Overview 12
- Firewall environments 14
- Load balancing paths 15
- Firewall selection 17
- Hashing mechanism 17
- Stateful FWLB 18
- Health checks 18
- Path health checks 19
- Application health checks 19
- Firewall health check debug 21
- Basic FWLB topology 22
- HA FWLB topology 23
- Failover 24
- Router paths 24
- Multizone FWLB topology 25
- FWLB configuration limits 26
- Configuring Basic FWLB 28
- IPv4 Firewall-1 37
- IPv4 Firewall-2 37
- External 40
- Internal 40
- Firewall-2 42
- Firewall-1 42
- Configuring HA FWLB 48
- Session limits 49
- Session aging 49
- Task Reference 52
- Configuring the firewall port 53
- Configuring the partner port 54
- Configuring the router port 55
- Configuring the firewalls 55
- Adding the firewalls 55
- Connection rate control 57
- Complete CLI example 62
- HA FWLB with VRRP 73
- Usage notes 78
- Configuring Multizone FWLB 82
- Zone 3Zone 2 84
- Zone1-SI(config)# no span 85
- Failover algorithm 92
- Commands on Zone1-SI-A zone 1 92
- DRAFT: BROCADE CONFIDENTIAL 100
- 53-1002436-01 102
- SI-A SI-A 104
- In this chapter 124
- NAT firewalls 124
- Extra firewall method 129
- Access policy method 130
- Specifying the partner port 134
- Specifying the router ports 134
- Configuring FWLB and SLB 146
- Configuring SLB-to-FWLB 148
- Configuring the real servers 149
- Enabling SLB-to-FWLB 150
- Configuring FWLB-to-SLB 152
- Enabling FWLB-to-SLB 154
- FWLB configuration overview 166
- TCP/UDP port statistics 169
- FWLB path information 172
- Field Description 173
- • 6 – TCP 174
- • 17 – UDP 174
- In this appendix 176
- FWLB selection algorithms 182
- Configuration guidelines 186
- Denying FWLB 187
Related products and manuals for Network switches Brocade Communications Systems ServerIron ADX 12.4.00
(12 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.374 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals