Brocade Communications Systems ServerIron ADX 12.4.00 Service Manual Page 66
- Page / 149
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
54 ServerIron ADX NAT64 Configuration Guide
53-1002444-02
Stateless NAT46 dynamic mapping configuration
4
DRAFT: BROCADE CONFIDENTIAL
The <holdoff-interval> variable is configured in seconds. Configurable values are from 10 through
3600 seconds. The default value is 180 seconds.
Prefetched NAT46 dynamic mapping configuration
The NAT46 gateway can be configured to prefetch dynamic mappings—to periodically send PTR
queries to the DNS server to determine the IPv6 address translations for the IPv4 destination
addresses specified. The NAT46 gateway uses this information to populate its mapping table.
Basic prefetched NAT46 dynamic mapping configuration tasks include the following:
• “Configuring NAT46 IPv6 prefixes with prefetched dynamic learning” on page 54
• “Configuring NAT46 IPv4 prefixes with prefetched dynamic learning” on page 54
• “Configuring NAT46 prefetched dynamic learning” on page 55
Advanced real-time NAT46 dynamic mapping configuration tasks include “Configuring NAT46
hold-off intervals for DNS discoveries” on page 55.
Configuring NAT46 IPv6 prefixes with prefetched dynamic learning
The NAT46 gateway uses a NAT46 IPv6 prefix to create a synthesized IPv6 source address on the
NAT46 gateway for each of the IPv4 clients. The synthesized IPv6 address is used to represent the
IPv4 clients to the IPv6 network.
Use the nat64 ipv6-prefix command to specify the IPv6 prefix. Enter a command such as the
following:
ServerIron ADX(config)# nat64 ipv6-prefix 2001:db8:8000::0/96 stateless
Syntax: [no] nat64 ipv6-prefix <prefix/length> stateless
The <prefix/length> variable specifies the NAT46 IPv6 prefix that will be used by the ServerIron
ADX when operating as a NAT46 gateway. Currently, the only supported prefix length is 96.
The stateless operand is required for stateless NAT46 gateway configurations. Only one IPv6 prefix
can be configured with this option.
Configuring NAT46 IPv4 prefixes with prefetched dynamic learning
In a NAT46 configuration, the IPv4 prefix defines the range of IPv4 addresses that can be used to
represent the IPv6 resources available to IPv4 clients.
Use the nat64 ipv4-prefix command to specify an IPv4 prefix with a subnet mask. Any IPv4 address
within the defined subnet can then be assigned to an IPv6 resource made available through the
NAT46 gateway.
Use the prefetch option to enable that the NAT46 gateway to pre-populate the mapping table such
as in the following command.
ServerIron ADX(config)# nat64 ipv4-prefix 200.1.1.0/24 prefetch
In this example, any IPv4 address within the subnet “200.1.1.x” can be assigned to an IPv6
resource in the IPv6-only network.
Syntax: [no] nat64 ipv4-prefix <prefix/subnet>[prefetch]
- ServerIron ADX 1
- Document History 2
- Contents 3
- About This Document 9
- Command syntax conventions 10
- Notice to the reader 11
- Related publications 11
- Getting technical help 11
- NAT64 and NAT46 Overview 13
- Stateless NAT46 translation 14
- Protocol support 15
- NAT64 fragmentation support 17
- References 18
- Stateful NAT64 Configuration 19
- Operation of stateful NAT64 20
- 53-1002444-02 23
- Enabling connection logging 28
- Displaying NAT64 information 31
- Displaying NAT64 translations 32
- Displaying NAT64 statistics 33
- Displaying NAT64 resources 37
- Stateless NAT64 Configuration 39
- Operation of stateless NAT64 40
- High availability for NAT64 52
- Clearing NAT64 information 53
- Stateless NAT46 Configuration 55
- Operation of stateless NAT46 56
- High availability for NAT46 67
- Displaying NAT46 information 68
- Clearing NAT46 information 69
- Access Control Lists 71
- Rule-based ACLs 72
- Default ACL action 74
- ACL IDs and entries 74
- Configuring rule-based ACLs 77
- Modifying rule-based ACLs 85
- Reordering ACLs 86
- Applying ACLs to interfaces 87
- Adding comments to named ACLs 89
- ACL logging 94
- Displaying ACL log entries 95
- Clearing the ACL statistics 97
- Throttling the fragment rate 98
- DRAFT: BROCADE CONFIDENTIAL 100
- Enabling strict TCP mode 101
- Enabling strict UDP mode 102
- ACLs and ICMP 103
- Numbered ACLs 104
- Named ACLs 105
- • Enable the strict TCP mode 107
- IPv6 Access Control Lists 109
- Configuration notes 110
- Processing of IPv6 ACLs 110
- Configuring IPv6 ACLs 111
- IPv6 ACL syntax 114
- Syntax Description 116
- Displaying IPv6 ACLs 118
- Logging IPv6 ACLs 119
- Network Address Translation 121
- Configuring NAT 122
- Configuring static NAT 123
- Configuring dynamic NAT 123
- Enabling IP NAT 124
- NAT configuration examples 125
- IP NAT with VIP overlap 129
- Translation timeouts 130
- Stateless static IP NAT 132
- IP NAT redundancy 133
- Displaying NAT information 144
- Displaying NAT translation 147
- Displaying VRRPE information 148
Related products and manuals for Network switches Brocade Communications Systems ServerIron ADX 12.4.00
(16 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 3.214 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals