Brocade Communications Systems VDX 8770-8 Installation Guide Page 41
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
When you have assigned the IP and gateway addresses to management interface 1/1, you should
also assign IP and gateway addresses to management interface 1/2 if you have installed a second
management module.
device(config)# interface Management 1/1
device(config-Management-1/1)# no ip address dhcp
device(config-Management-1/1)# ip address 10.24.85.81/20
device(config-Management-1/1)# ip gateway-address 10.24.80.1
NOTE
The ip gateway-address command will not be available on the device if the Layer 3 or Advanced
license is installed. In that case, use the following command sequence
switch(config)# rbridge-id 1
switch(config-rbridge-id 1)# ip route 0.0.0.0/0 <default-gateway>
If you are going to use an IPv6 address, enter the network information in semicolon-separated
notation as prompted after the ipv6 address operand. You should also disable DHCP.
device(config)# interface Management 1/1
device(config-Management-1/1)# no ip address dhcp
device(config-Management-1/1)# ipv6 address \
fd00:60:69bc:832:e61f:13ff:fe67:4b94/64
7. Return to privileged EXEC mode by entering exit .
device(config)# exit
device#
8. To display the configuration, use the show running-config interface Management command.
device# show running-config interface Management 1/1
interface Management 1/1
no ip address dhcp
ip address 10.24.85.81/20
ip gateway-address 10.24.80.1
ipv6 address fd00:60:69bc:832:e61f:13ff:fe67:4b94/64
no ipv6 address autoconfig
!
Logging off the serial console port and disconnecting the serial cable
You can use the serial port to monitor error messages through the serial connection. If the serial port is
no longer required, use the logout command to log out of the serial console, remove the serial cable,
and replace the protective plug in the serial port.
Establishing an Ethernet connection
After using a serial connection to configure the IP addresses for the device, you can connect the active
management module to the local area network (LAN).
NOTE
Connecting the management modules to a private network is recommended.
By establishing an Ethernet connection, you can complete the device configuration using a serial
session, Telnet, or management application, such as Brocade Network Advisor.
Logging off the serial console port and disconnecting the serial cable
Brocade VDX 8770-8 Hardware Installation Guide 41
53-1002564-07
- Brocade VDX 8770-8 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- Product Overview 11
- Hardware components 12
- Port side view 13
- Nonport side view 14
- Supported Line cards 15
- Breakout mode 16
- Trunking 16
- 27x40 GbE operating modes 17
- High availability 18
- Device Installation 19
- NEBS requirements 21
- Environmental requirements 25
- Chassis slots 25
- Port numbering 26
- FIGURE 4 12x40 GbE line card 27
- 48x10G-T port numbering 28
- 27x40 GbE port numbering 29
- 6x100 GbE port numbering 30
- Providing power to the device 31
- Connecting an AC power cord 32
- Connecting a DC power cord 32
- Initial Configuration 35
- Configuration tasks 36
- Changing the RBridge ID 39
- Assigning permanent passwords 39
- Configuring the IP addresses 40
- Customizing a host name 42
- Customizing a chassis name 42
- Setting the date and time 43
- Setting the time zone 44
- Verifying correct operation 46
- Backing up the configuration 47
- Connecting network devices 47
- Testing connectivity 48
- Managing cables 49
- System Monitoring 51
- 8x10 GbE line card 52
- 12x40 GbE line card 53
- 27x40 GbE line card 53
- 48x10G-T line card 55
- 6x100 GbE line card 56
- 1 Power LED 62
- 2 Status LED 62
- 1 AC power input LED (AC OK) 63
- 2 DC power output LED (DC OK) 63
- 3 Alarm LED (ALM) 63
- Introduction 69
- ESD precautions 69
- Time and items required 70
- Removing a line card 72
- Replacing a line card 73
- Removing a management module 75
- Replacing a management module 76
- Removing an AC power supply 80
- Replacing an AC power supply 81
- Removing a DC power supply 82
- Replacing a DC power supply 82
- Fan removal and replacement 83
- Replacing a fan 84
- Removing an air filter 86
- Replacing an air filter 86
- Removing a filler panel 86
- Replacing a filler panel 87
- Removing a transceiver 89
- Replacing a transceiver 90
- Removing a QSFP transceiver 90
- Cable routing table 91
- System specifications 95
- Ethernet 96
- Power consumption (modules) 100
- Memory specifications 102
- Regulatory compliance (EMC) 102
- 53-1002564-07 103
- Regulatory Statements 105
- VCCI statement 106
- China ROHS 106
- FCC warning (US only) 106
- Cautions and Danger Notices 107
- Danger Notices 112
- Electrical dangers 113
- Laser dangers 116
Related products and manuals for Network switches Brocade Communications Systems VDX 8770-8
(188 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.552 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals