Brocade Communications Systems NetIron CER Series Installation Guide Page 97
- Page / 120
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3. Gently insert the cable connectors (a tab on each connector should face upward) into the port
connectors until the tabs lock into place.
4. Observe the link and active LEDs to determine if the network connections are functioning properly.
DANGER
The intra-building port or ports of the equipment or subassembly is suitable for connection to
intra-building or unexposed wiring or cabling only. The intra-building port or ports of the
equipment or subassembly MUST NOT be metallically connected to interfaces that connect to
the outside plant (OSP) or its wiring. These interfaces are designed for use as intra-building
interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE, Issue 5) and require
isolation from the exposed OSP cabling. The addition of Primary Protectors is not sufficient
protection in order to connect these interfaces metallically to OSP wiring.
Tunable 10 GbE DWDM SFP+
NOTE
Tunable 10 GbE DWDM SFP+ are only supported on NetIron CES and NetIron CER 4x10G models
only.
The tunable 10 GbE dense wavelength-division multiplexing (DWDM) SFP+ modular optic (part number
10G-SFPP-ZRD-T) can be configured through the CLI to use C-band channels 1 - 102 for flexible metro
or campus Ethernet links that reach up to 80 km.
For 10-Gigabit Ethernet DWDM interfaces only, configure full C-band tunable optics as shown below.
To configure a physical port, enter a command such as the following.
device(config-if-e10000-1/1)# tunable-optic sfpp channel 5
Syntax: tunable-optic sfpp channel channel number [ show ]
To configure a LAG port, enter a command such as the following.
device(config-if-e10000-1/1)# physical-port 1/1 tunable-optic sfpp channel 5
device(config-lag-lag1)# physical-port 1/1 tunable-optic sfpp channel 5 show
Channel 5: 191.3THz, 1567.13nm
Syntax: physical-port port tunable-optic sfpp channel channel number [ show ]
Use the channel number parameter to specify the channel number to use on the interface. Possible
values 0 through 102.
Use the show options to display the SFPP channel used on the interface.
Fiber optic connector cleaning
To avoid problems with the connection between the fiber optic module (SFP (mini-GBIC), SFP+, or
XFP) and the fiber cable connectors, Brocade strongly recommends cleaning both connectors each
time you disconnect and reconnect them. In particular, dust can accumulate in the connectors and
cause problems such as reducing the optic launch power.
To clean the fiber cable connectors, Brocade recommends using the fiber-optic reel-type cleaner that
shipped with your device. You can also purchase this type of cleaner from the following web site.
http://www.fisfiber.com/
Tunable 10 GbE DWDM SFP+
Brocade NetIron CES 2000 Series and NetIron CER 2000 Series Hardware Installation Guide 97
53-1003263-02
- Brocade NetIron CES 2000 1
- Series and NetIron CER 1
- 2000 Series 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- About This Document 11
- Notice to the reader 12
- Related publications 13
- Product Overview 15
- Product overview 20
- Software features 21
- Upgrade applications 21
- Hardware features 22
- Control features 29
- Network interfaces 31
- Supported optics 31
- 10 Gigabit Ethernet ports 32
- Port regions 33
- Power supplies 34
- AC power supplies 35
- DC power supplies 35
- Cooling system and fans 36
- Password assignment 39
- IP address configuration 40
- Support of sub-net masks 41
- Device connection 43
- Installation 45
- Summary of installation tasks 46
- Installation precautions 47
- Installation site preparation 49
- Installing an AC power supply 50
- Installing a DC power supply 52
- Device installation 55
- Mid rack mount position 57
- Reverse rack mount position 58
- System power 59
- Operation verification 60
- Verifying proper operation 61
- PC or terminal attachment 63
- CLI Functionality 65
- Online help 66
- Command completion 66
- Scroll control 66
- Line editing commands 66
- Hardware Specifications 73
- Physical dimensions 74
- Operating environment 76
- Storage environment 76
- Safety agency approvals 77
- Electromagnetic approvals 77
- Port specifications 77
- Console port pin assignments 78
- Hardware Maintenance 81
- AC power supply 83
- Required tools 84
- Removing the DC power supply 86
- Replacing the fan tray 94
- Cabling a fiber optic module 96
- Tunable 10 GbE DWDM SFP+ 97
- Regulatory Statements 99
- China CC statement 100
- FCC warning (US only) 101
- VCCI statement 101
- Caution and Danger Notices 103
- Electrical cautions 105
- Danger Notices 110
- General dangers 111
- Electrical dangers 111
- Laser dangers 115
- 53-1003263-02 117
Related products and manuals for Network switches Brocade Communications Systems NetIron CER Series
(46 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.753 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals